Inline FabricationTitan ReloadingMidSouth Shooters SupplyLee Precision
RepackboxSnyders JerkyLoad DataReloading Everything
RotoMetals2 Wideners
Results 1 to 9 of 9

Thread: 22lr to 223 projectiles

  1. #1
    Boolit Mold
    Join Date
    Mar 2011
    Posts
    10

    22lr to 223 projectiles

    I recently got around to using my kaine dies. I followed the directions the best i could. I measured my boolits and they measure 224 for the most part except where the rims used to be. I know they should be 224. They measure mid to high 224 at the rims. I annealed before i removed the rims. Are these safe to shoot? One guy i was talking to said this is normal and calls it a pressure bump. Thanks.

  2. #2
    Boolit Master

    rancher1913's Avatar
    Join Date
    May 2015
    Location
    plains of colorado
    Posts
    3,645
    anneal after you derim.
    if you are ever being chased by a taxidermist, don't play dead

  3. #3
    Boolit Mold
    Join Date
    Mar 2011
    Posts
    10
    I hear some do. The instructions say otherwise.

  4. #4
    Boolit Master

    Join Date
    Feb 2008
    Location
    Bozoland Mt.
    Posts
    1,698
    Slightly larger than .224 bases might cause a little higher pressure. So start with a reduced powder charge.
    Just like every other new load.
    To lazy to chase arrows.
    Clodhopper

  5. #5
    Boolit Master

    rancher1913's Avatar
    Join Date
    May 2015
    Location
    plains of colorado
    Posts
    3,645
    Quote Originally Posted by ekg98 View Post
    I hear some do. The instructions say otherwise.
    your having problems doing it by the instructions, try doing it a different way if you want different results.
    if you are ever being chased by a taxidermist, don't play dead

  6. #6
    Boolit Master
    Join Date
    Mar 2012
    Posts
    760
    You may want to use a Lee Universal Expander Die to open the mouth a little. If you annealed and used pure lead those bullets are going to be soft. Much softer than cast. Try smashing one with a hammer. They may squish down a little when you load them into the case. You can try pulling one after you load and crimp.

  7. #7
    Boolit Buddy
    Join Date
    Nov 2015
    Location
    wisconsin
    Posts
    109
    We are talking about a 1/2 of a thousandth of an inch. Variations in case capacity, primer make, powder lot numbers and especially seating depth will contribute more to pressure spikes than .0005 of bullet diameter. Rimfire jackets are GENERALLY more fragile so I keep my loads below maximum anyway and that is usually the sweet spot for these bullets. I know a guy (Stanley ) who believed the reloading manuals were dumbed down and safety'ed up so he knew he could always put an extra grain or 2 of powder to get the full potential of any cartridge. He's ok still but I haven't been shooting with him since 1997. Starting loads like the other guy said above me.

  8. #8
    Boolit Bub
    Join Date
    Jan 2006
    Posts
    34
    That sounds like a guy back home. Everyone called him gi joe but now it’s one eye Frank. He lost one to shrapnel.

  9. #9
    Boolit Master OldBearHair's Avatar
    Join Date
    Jul 2014
    Location
    Conroe TEXAS
    Posts
    671
    Quote Originally Posted by contendernut View Post
    That sounds like a guy back home. Everyone called him gi joe but now it’s one eye Frank. He lost one to shrapnel.
    Best three short sentences I've heard! Right to the point.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check