Anyone save the Brian Pierce New Vaquero level 11 23,000 psi 45 colt data?

[Tripplebeards]

Apparently rifle magazine load data doesn't go back that far with their magazine articles on their website anymore. If someone has it can they post the article for me?

[Wheelguns 1961]

I had that article saved on my computer, and one day I clicked on the link and it was gone. They did something to deny access.

[MT Gianni]

I got burned with that as well. I now copy, paste and save as document files. I didn't with that article.

[frogleg]

PM sent

[Tripplebeards]

PM sent

Thanks, sent you my email.

[Tripplebeards]

I’ll post the one Frogleg sent me. It’s a different one than the article I was thinking of using a 285 grain boolit that was loaded around a 1000 FPS and under 23,000psi. Frogleg, do they have an OAL listed for these loads?

[frogleg]

Sorry thats all I have saved. just clipping of the june 2002 article let me know the month and year of the article you are wanting I may have a digital copy of that issue of Handloader.

[navyvet]

Would Guns & Ammo John Taffin 45 Colt Load Data help?
https://www.gunsandammo.com/editoria...ad-data/370003

[boatswainsmate]

This is what I found in my load data stash. I hope it helps. http://buffalobore.net/HandloaderDecJan2012.pdf

[Tripplebeards]

Sorry thats all I have saved. just clipping of the june 2002 article let me know the month and year of the article you are wanting I may have a digital copy of that issue of Handloader.

It was hand loader magazine number #246

I called and Wolf publishing Co. will sell me the magazine with the article in it for $10. I was hoping someone downloaded and saved the article to save the time and money.


This was the link everyone posted for it. It just goes to the a wild Website now...

http://www.riflemagazine.com/magazin...246partial.pdf


I went in their website and saw the cover. It says April 2007 a d has two super RedHawks on it.



There is also a rifle #246 magazine but I am Guessing it’s in the handloader issue.

[boatswainsmate]

Issue 246 was for the 45-270-SAA Solid Bullet. Do you have a load data account? If so just look up 45 Colt and a 280 grain bullet. 20000 PSI Loads

[Tripplebeards]

I don’t have a load data account. If someone dose if they could please look up 255 grain and 280 grain boolits at 20,000 cup? I have some group buy group buy .452” 275 grain HPs that I casted up before selling off the mold. They’ll be 280 grains by the time I GC and PC them.

[Dale53]

Tripplebeards;
Here is a link to my Dropbox for that file:

https://www.dropbox.com/s/2v9v0xde84...rtial.pdf?dl=0

Just click on the link and download it.

Dale53

[Tripplebeards]

Thanks! Got it and downloaded it to my iPad abs also saved each page in my photos. I re posted it so other members don’t have to click in the download. Thanks Again!

[Dale53]

Triplebeards;
As always, I am happy to help out!

Dale53

[Tripplebeards]

Triplebeards;
As always, I am happy to help out!

Dale53

I’m sure there’s many other posters here that are appreciated your help as well. Thanks again!!!

What’s interesting is the VV- 3N37 at 11 grains and only 14,000 PSI. Most the 20,000 CUP load don’t get that much velocity. A powder I have never seen on the shelf anywhere Since I started reloaded 20 years ago.

I have these i cased up from our group buy before I pawned off the mold. I casted up about 15 pounds of them if I had to guess. I was disgusted with my 450 for the master bolt action because it wouldn’t feed so the mold went away. They are on average about 278 grains if I remember so with a GC I’m sure they’ll be 280 grains. I casted them up in 50/50 at 10.4 Bh. I figured they would work good for the loads above. Hopefully enough velocity and energy for deer hunting out 100 yards at a 1000 FPS MV.



I tested a few out of in line muzzle loader last year. They are clear PC’d.


So food for thought...I would assume a 14,000 load with a MV of 1000 FPS is going to have exact same felt recoil as a 1000 FPS, 20,000 CUP load with all other things equal other then pressures?

[jreidthompson1]

I’m sure there’s many other posters here that are appreciated your help as well. Thanks again!!!

What’s interesting is the VV- 3N37 at 11 grains and only 14,000 PSI. Most the 20,000 CUP load don’t get that much velocity. A powder I have never seen on the shelf anywhere Since I started reloaded 20 years ago.

Powder valley *claims* to have it in stock


https://www.powdervalleyinc.com/prod...htavuori-3n37/

Sent from my SM-N950U using Tapatalk

[Tripplebeards]

Powder valley *claims* to have it in stock


https://www.powdervalleyinc.com/prod...htavuori-3n37/

Sent from my SM-N950U using Tapatalk

Thanks
I won’t order powder on line because of the expensive haz mat costs.

[Tripplebeards]

I went to my LGS today. They had one pound of HS-6 left for $26.99, one pound of tite group left for $21.99, and four cans of universal for $26.99 each. I rolled the dice and bought the HS-6. I read a few posts that shooters were getting good accuracy with a 13 grain charge and a 280 grain cast boolit.

[Tripplebeards]

I’d like to try 255 grains with HS-6 tier 2 loads but can’t find any listings. Can I use the 280 grain data?

I did load up a ladder test from 12 to 13.5 grains with the 280 grain HP. They are 50/50 alloy, PC, and GC. Loaded to 1.650” when I crimped them the boolot is seated deep enough that it just looks like a taper crimp.




Whoops, guess I should have read the load data frogleg sent me. Looks like 12.5 grains of HS 6 is the max with a 255 grain boolit to stay within 19,000 psi. Weird that I can use 13.5 grains with a 280 grain boolit and only 12.5 grains with a 255 grain boolit for some reason???