If used in the same cartridge, at equal velocity, and approximately the same boolit weight, how does a round nose flat point compare to the semi-wadcutter (Keith type) in effectiveness on game?
Thanks in advance.
Dipperman
If used in the same cartridge, at equal velocity, and approximately the same boolit weight, how does a round nose flat point compare to the semi-wadcutter (Keith type) in effectiveness on game?
Thanks in advance.
Dipperman
"Close only counts in horseshoes and hand grenades." D. Paulson
Per Elmer Keith, round nose zips right through; no stopping power.
Britons shall never be slaves.
I think it depends on the individual design, or size of the meplat. Bigger meplat, more damage.
Due to the price of primers, warning shots will no longer be given!
My experience on deer and hogs has been that in soft 8-10 BHN alloy at subsonic revolver velocity in calibers similar to the .44-40 or .45 Colt, for bullets of the same weight and diameter of meplat, it makes absolutely no difference whatever.
The ENEMY is listening.
HE wants to know what YOU know.
Keep it to yourself.
Larry Gibson
“Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.”
― Nikola Tesla
Graphs generated using MacPherson WTI model for .38 Special+P 158-grain at 940 fps, for full wadcutter, SWC and LRN nose shapes, presuming NO expansion:
Attachment 264087Attachment 264088Attachment 264089
The ENEMY is listening.
HE wants to know what YOU know.
Keep it to yourself.
The wider the flat the more energy transfer with all else being equal. But if there is only a very small diameter difference in the flats then the target probably will never indicate much difference.
The big overlooked advantage with the SWC is if you will look at it from the nose nearly the whole diameter is flat whereas the FN round nose only has that flat on the nose.
Plus the SWC has a structural advantage. That sub diameter nose sitting out there will expand more rapidly than a RN structure again all other factors being the same.
Mike in LLama Land
"Come unto Me, all you who labor and are heavy burdened, and I will give you rest." Matthew 11:28
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
The solid soft lead bullet is undoubtably the best and most satisfactory expanding bullet that has ever been designed. It invariably mushrooms perfectly, and never breaks up. With the metal base that is essential for velocities of 2000 f.s. and upwards to protect the naked base, these metal-based soft lead bullets are splendid.
John Taylor - "African Rifles and Cartridges"
Forget everything you know about loading jacketed bullets. This is a whole new ball game!
Well somewhere down along that wound channel it has to start causing drag / damage.
"Come unto Me, all you who labor and are heavy burdened, and I will give you rest." Matthew 11:28
Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.
"Considering the splash effect, I doubt the shoulder ever touches flesh."
That does seem to be the prevailing theory proffered by proponents of the WFN style of bullet. However, as i mentioned earlier I never have seen any real terminal difference between a hard cast SWC vs a hard cast WFN given the same cartridge, bullet weight and velocity. A quicker death will result from more damage to vital organs. I've read of "improved" terminal performance of the WFN, especially in handgun cartridges. However, as previously stated I have not seen it with numerous deer hunted and deer/livestock "put down" when injured.
Where I have seen a marked difference of improved terminal effectiveness [as in quickness of kill and lessor distance traveled after shot] has been with either bullet cast of softer more malleable alloy that gives proper expansion. Proper expansion provides for more terminal damage, that is a fact that is well known and proven.
Larry Gibson
“Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.”
― Nikola Tesla
Get a copy of Veral Smith's little blue book. His claims are that putting grease on a swc's shoulder and shooting into recoverable material show the shoulder of a swc never even hit paper on a target.
For me the answer is that assuming equal meplates you would get equal results. Most swc's are smaller in the meplate than rf's. Are they enough to do the job? generally yes but it depends on the job you ask it to do. IME, an 80 lb whitetail takes less to kill than a 350 lb cow elk.
[The Montana Gianni] Front sight and squeeze
I've been trying to buy his book for 2 years. The guy refuses to answer a phone or email. I can promise you the shoulder on a SWC touches the paper. That's why the SWC exists! It cuts a clean, full diameter hole in paper just like a wadcutter.
Does it touch meat in an animal? I'm not so sure about that one. From what I'm finding, the nose on a RNFP and your Elmer Keith SWC are pretty much the same in all calibers. All being around that 65%-70% ish range. Of course there are thousands of variations of each, it's hard to generalize.
I have little experience hunting with hard cast, solid, non-expanding bullets. I wasn't impressed with them. Many disagree with me. Lots of proponents of the WFN, but when I saw what a 357 mag did compared to a 44 mag, both with Keith SWC's, I just didn't see much difference in the wound on a whitetail. That's a .250" meplat vs a .275" meplat.
When I showed a former muzzle loader and BPC shooter and hunter the slightly concave wide nose on the Lee 44cal 305gr bullet, he was impressed. He predicted that bullet's sharp edge at its nose would grab soft tissue for a bigger wound channel, and of course it is heavy enough to break bone.
Back in the 1990s, Ross Seyfried tested this in one of the slicks (Guns & Ammo?). He mixed up pails of jello filled with sand and fired both LFN and SWC bullets (.45”?) painted with black paint into the gel. The photos definitively showed that the SWC shoulders had no abrasion, they were still covered with paint. The noses of all bullets were void of paint. At the test velocity, the SWC shoulder didn’t touch anything, indicating that wounding is performed by the bullet’s nose.Considering the splash effect, I doubt the shoulder ever touches flesh.
.
My own terminal ballistics test showed that, while the RNFP penetrate slightly farther, the difference isn't meaningful.
I would like to express my sincere appreciation and thanks to everyone who responded to my question. Your responses have been very informative and helpful.
Thank you all very much,
Dipperman
"Close only counts in horseshoes and hand grenades." D. Paulson
As the real answer is bullet placement, the rest is to close to argue about. Put either one in the right place, dead is dead.
CF
Vote Independent, vote Republican, vote Democratic, just don’t vote Incumbent!
I believe in the Bible, Freedom, the Constitution, the Bill of Rights and personal responsibility. My government believes I am narrow minded, intolerant and dangerous.
I too have always questioned whether the shoulder did any work. However I can say that my 454-424 cut a clean 45 cal hole at the entrance on deer.
The lee 452-255RF has the same meplat “.320 “ and cuts about the same hole just not as clean as the semi wadcutter.
Like others have said I can’t tell a difference in terminal performance.
With a small cup HP in either blood trails are better if/ when it exits but terminal performance remains about the same.
For the record I deer hunt with the NOE copy of the Lee with a cup Hp. Performance has been excellent on several deer. I see no reason to change.
Some people live and learn but I mostly just live
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |