The solid soft lead bullet is undoubtably the best and most satisfactory expanding bullet that has ever been designed. It invariably mushrooms perfectly, and never breaks up. With the metal base that is essential for velocities of 2000 f.s. and upwards to protect the naked base, these metal-based soft lead bullets are splendid.
John Taylor - "African Rifles and Cartridges"
Forget everything you know about loading jacketed bullets. This is a whole new ball game!
with the 30-30 being responsible for probably a majority of dead deer in North America I would think its very likely that the 311291 will work equally as well as the 311041
So if you hunt pails of jello the shoulder doesn't matter. Think about what you aim to hit shooting at a deer. Are those areas homogenous and jello like? Ever hit a bone? What then?
By the way Brian Pearce firmly believes the shoulder cuts in big game and has both shot and butchered piles of game with both types.
Rule 303
deer I have shot with the 410459 left cookie cutter holes in hide and shoulder blade. Also in the messing around I have done the Saeco 230 .411 does not tend to cookie cut but the 410459 does, so it seems that the diameter of the first shoulder band might have something to do with the end hole. I love the Keith, but my biggest hole cutter is a two .33 meplat WLNGC-- I have now have a NOE keith with a .31 meplat and a good shoulder-- we will see how it does.
I take my observations from two sources.
1) I butcher deer semi-professionally with my wife during the season. Not only do I butcher my own, but from about a dozen other people every year. So I see a lot of wounds. Where I live pistol calibers are popular (they were legally required until recently) and so are muzzloaders. Friendship, Indiana is Muzzloader capital of the world, basically. Shotguns were popular too until the last few years.
2) From research personally conducted on calibrated gelatin.
There is very little observable difference between round nosed and flat nosed projectiles at normal handgun velocities, basically. On gelatin it is almost indistinguishable. I have a 158 grain RCBS SWCGC and a 158 grain SAECO roundnose. Using the exact same charges in both 357 and 38 special fired from my 4" model 19 I could hardly tell any difference. In both cases the bullets zippled straight through 28" of gel. The flat nose does seem to do a little more damage in the initial few inches, but it is really almost negligible. Hollowpoints are a different ball game.
On actual animals the difference is slightly more observable. Flat nosed projectiles seem to crush up a little more meat in the wound channel whereas round nose sort of "pushes" it out the way more. In both cases though it does leave a hole, roughly caliber sized, as these projectiles do not expand.
Now, I've seen wounds from 12 gauge lee slugs moving at about 1700 FPS at impact. Despite having an almost spherical nose, these things DO smash into a sort of fat pancake shape leaving an enormous 1" or so hole in the animal. I've never observed slugs impacting at lower handgun type velocities so I don't know what to about that. These are cast of nearly pure lead.
For me I prefer flat noses for other reasons. 1) flat nosed top punches have a lot more surface area on the bullet and don't mark it up when you lubricate/size. 2) Larger bullets can be loaded in revolvers since it wont go too far forward of the cylinder. 3) If you shoot paper the wadcutter or semi-wadcutter usually leaves a nicer hole.
Good info. I can see both sides. I have always used long SWCs as I am a definite Grey Beard. I haven't used WFN on game but many who have swear by them.
SWCs and RNFPs designs like LFN, WFN are basically the same except for the shoulder and the size of the meplat. The difference in meplat is usually less than 15% in a given caliber, so I am not sure why anybody would expect radically different performance.
Roundnose is a different profile, so I could imagine there would be differences, but my observations do not bear out much difference.
One performance difference I've noticed is flight.
Ketih type SWCs, RN, RNFP, etc...these a pretty good at maintaining stable flight at extended ranges and as they cross the transonic zone (which is an issue with magnum handungs which start off super sonic but often fall to below subsonic at practical ranges). Full-Wadcutters, though very accurate at short ranges, just fall apart stability wise at pretty near ranges. I've seen them start to tumble and keyhole at only 30 yards or so.
I like the solid Ketih-type SWC in larger bores probably best of all because it is so versatile. It cuts a nice hole in paper, has adequate weight to pass through basically any game, is not so heavy it is brutish to shoot, are usually accurate, have stable long range aerodynamics, and can be loaded to mousfart and magnum power levels and works well in both. Really, what more do you want? Gas checks are helpful sometimes, and especially with hollowpoints or when pressures get high, and thats where Ray Thompson designs come in.
I prefer RNFPs in medium bore handguns and rifles. The MP 359 hammer (which is basically a WFN pattern) with gas check is an outstanding bullet in both my M19 and Marlin.
I would never think of using a 30 caliber or smaller without a gas check. Cleaning lead from a barrel that narrow is a chore. All my 30 caliber molds are checked and RNFPs.
Last edited by curioushooter; 07-10-2020 at 12:45 PM.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |