RotoMetals2Lee PrecisionTitan ReloadingWideners
Reloading EverythingRepackboxLoad DataInline Fabrication
MidSouth Shooters Supply
Page 1 of 2 12 LastLast
Results 1 to 20 of 23

Thread: MP Molds 312-85-RF

  1. #1
    I'm A Honcho!
    Join Date
    Nov 2006
    Posts
    1,306

    MP Molds 312-85-RF

    MP Molds 312-85-RF 3 Cavity Brass Cramer Plain Base or Gas Check mold Hollow Point mold on the two cavity blocks or a 6 cavity brass solid PB or GC on the four cavity blocks or an 8 cavity solid PB or GC on the aluminum blocks. This is a new design intended to fill a hole in the MP line-up for 32 caliber handguns and 30 caliber rifles. This is a 640 style nose on this bullet. You have the option of 0.312" and 0.314" as cast sizes and easily sizes smaller. The weight is as shown on the drawing dependent on your alloy of choice.

    This bullet fits in all the Ruger Revolvers and Single actions (32 H&R Mag and 327 Federal Mag), 32 ACP semi-auto handguns, all the 32 Short, 32 S&W Long, 32 Colt New Police and older revolvers. It fits most of the 32-20 revolvers as well as 30 Luger, 30 Mauser and 7.62 Tokerev semi-autos.

    We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.

    I am offering these choices: Brass 3 cavity PBHP, Brass 3 cavity GCHP, Brass 6 cavity PB solid, Brass 6 cavity GC solid, Aluminum 8 cavity PB solid and Aluminum 8 cavity GC solid. Your choice of 0.312" or 0.314" diameters.

    Pins included are: For the Hollow Point Molds are 1) Large HP pin, 2) Medium Penta HP pin, 3) Cup HP pin, 4) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.

    Prices are:
    3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off.........
    I will have to get the other prices.

    Sequence of events:
    Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.

    Prices are somewhat variable due to the exchange rate.... be aware of this.

    Post your disguised e-mail address as follows please: imashooter AT gmail DOT com, mold choice, number of cavities, base style (PB or GC), either 0.312" or 0.314" (or both) and number of molds wanted (one to however many).


  2. #2
    Boolit Buddy
    Join Date
    Dec 2010
    Location
    Holden Ma
    Posts
    177
    I’ll take a 3 cavity .314 HPGC . Email is thadd3220 at yahoo dot com

  3. #3
    Boolit Master

    mattw's Avatar
    Join Date
    Oct 2014
    Location
    East Central Illinois
    Posts
    1,796
    I’ll take a 3 cavity .314 HPPB. Email mattlward AT gmail DOT com.

  4. #4
    Boolit Buddy
    Join Date
    Jul 2009
    Location
    CT
    Posts
    110
    I’ll take a 3 cavity .314 HPPB. Email is eagle-rain AT cox DOT net.

  5. #5
    Boolit Buddy
    Join Date
    Jul 2019
    Posts
    115
    I'll take a 3 cavity .314 HPGC. Email is cstephensonrc AT gmail DOT com.

  6. #6
    Boolit Buddy
    Join Date
    Jul 2007
    Location
    Tasmania Australia
    Posts
    396
    G'Day I'd like a 3 cav .314 hpgc mold please. namovlov at bigpond dot com

  7. #7
    Boolit Buddy

    Join Date
    Jan 2013
    Location
    the other Louisiana
    Posts
    216
    If this can be done without lube grooves, I would be in for two 3 cavity .314 HPGC NLG molds. jbpaul AT suddenlink DOT net .

    Thanks,
    JB
    "He's whittlin' on a piece of wood. I've got a feeling when he stops whittlin', somethin's gonna happen." - Cheyenne, Once Upon a Time in the West (1968)

    "When you have to shoot, shoot. Don't talk." - Tuco, The Good, the Bad and the Ugly (1966)

  8. #8
    I'm A Honcho!
    Join Date
    Nov 2006
    Posts
    1,306
    Seven molds.

  9. #9
    Boolit Master
    Join Date
    Apr 2009
    Location
    northern Minn. in the boonies
    Posts
    2,175
    I would like a 3 cav. PB at .312 kbsten 1 at arvig dot net

  10. #10
    Boolit Master
    NoZombies's Avatar
    Join Date
    May 2009
    Location
    N. Florida
    Posts
    2,493
    Sign me up for an 8 cavity Al PB and a 3 cavity HPPB please.

    tony at *my username* com (replace *my username* with my actual username)
    Nozombies.com Practical Zombie Survival

    Collecting .32 molds. Please let me know if you have one you don't need, cause I might "need" it!

  11. #11
    Boolit Bub
    Join Date
    Dec 2014
    Posts
    54
    I'll take a 3 cav .314 hppb
    Fav41 at protonmail dot com

    Sent from my SM-G973U using Tapatalk

  12. #12
    Boolit Buddy
    FLYCUTTER's Avatar
    Join Date
    Mar 2010
    Posts
    449
    Since this is a discussion, why not a 4 cavity w/all pins. 4 cavity is a normal mold for Mihec. If that was going to change I would be in for one.

  13. #13
    Boolit Master gtgeorge's Avatar
    Join Date
    May 2011
    Location
    Deer woods of GA
    Posts
    617
    I’ll take a 3 cavity .314 HPPB. Email gspatton AT gttransmissions DOT com.

  14. #14
    Boolit Buddy
    Join Date
    Dec 2010
    Location
    Holden Ma
    Posts
    177
    For thadd3220 @ yahoo please make mine a PB thank you

  15. #15
    Boolit Mold
    Join Date
    Jun 2020
    Location
    South Arkansas
    Posts
    23
    Is this group buy still open? I would like to get in on a .32 mould.

  16. #16
    Boolit Master
    Join Date
    Sep 2008
    Location
    NY/VT Border
    Posts
    527
    Perhaps this buy should have a few cartridges listed in the heading. (30 Mauser, 7.62x25, 7,65 french long). I feel like there are a lot of people looking for the perfect 30 mold for all those 30 autoloaders. I'm surprised this isn't hot, as it fills the gap for the one type of autoloading pistol that there hasn't been an MP mold for.
    Need advice fixing a coleman appliance? Maybe I can help!

  17. #17
    Boolit Buddy
    Join Date
    Dec 2010
    Location
    Holden Ma
    Posts
    177
    Yes I agree . And also typically when ppl see a sign up list it seems people are a little more interested. The way it appears, is this is still a discussion. Just my .02 cents worth what you paid for . Just hoping to gain some attention for this one

  18. #18
    Boolit Buddy SoonerEd's Avatar
    Join Date
    Sep 2020
    Location
    Madison, MS
    Posts
    323
    Put me down for an aluminum 8 cavity PB solid in .312. I'll be using this for a 7.62x25 TT-33 Tokarev.

    ed at trilogy-health dot com.
    Last edited by SoonerEd; 04-25-2021 at 11:23 PM.

  19. #19
    Boolit Buddy SoonerEd's Avatar
    Join Date
    Sep 2020
    Location
    Madison, MS
    Posts
    323
    Is this discussion still active or has it died?

  20. #20
    Boolit Man
    Join Date
    Nov 2009
    Location
    TX
    Posts
    96
    Bump.

    If this one ever makes it to active I would go for a three cavity .314 PB brass mold. sethdoty 444 at hot mail dot com.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check