It just works.
Sent from my SM-G960U using Tapatalk
It just works.
Sent from my SM-G960U using Tapatalk
Paper targets aren't your friends. They won't lie for you and they don't care if your feelings get hurt.
Great load and packing gun. Is that a Bowen rear sight? Also see a Super hammer, looks better.
Bowen sight, super hammer, belt mountain pin, and a 9mm cylinder. One versatile six gun.
Paper targets aren't your friends. They won't lie for you and they don't care if your feelings get hurt.
Very nice ,sir. I've settled on 14 gr. 2400 with the H&G #51. Works well on the Ruger SS and the Rossi 92.
A good mate to that would be the .45 Colt/ .45 A.C.P. model. Cover 5 cartridges in two weapons.
I like the same load, 13.5 gr of 2400, with Lyman's 358156GC in Magnum cases.
Sized 0.358" for the Rugers and Smiths, and 0.360" for the Marlin, that bullet gives me 1-1/2" gps at 25 yds from the short guns, and the same at 100 yds with the Marlin, (with visually inspected bullets, tho not weighed). The Mihec equivalent bullet does as well, MP360156 as I recall.
It's my standard .357 Magnum load and gives me a chrono'd 1150 fps from a 4" Smith M66 & M19. I've not chrono'd the Marlin, but suspect it's over 1550 fps. I've found it comfortable in the 4" K frames and Ruger BH's, and even more so in an N frame M27. My M60 with a 3" bbl., however is a handful and then some with it. It's a J frame but with good Hogue combat uni-grips installed and still kicks like a mule.
I've killed a cpl deer with that bullet; both with a 3" bbl'd Smith M60 that I was carrying while helping a neighbor track down a wounded buck in one case and a doe in the 2nd. Both were neck shots from ~20 yds and gave complete penetration while clipping the spine.
Best regards, Rod
Rod
I have loaded the 358156 ahead of 13.5 grains of 2400 in 38 Special cases. Used the lower crimp groove to give a little more capacity. Great load for the 38/44 Heavy Duty.
Kevin
Last edited by StrawHat; 04-06-2020 at 07:46 PM.
Knowledge I take to my grave is wasted.
I prefer to use cartridges born before I was.
Success doesn't make me happy, being happy is what allows me to be successful.
Picked up 8 lbs of 2400 before the pandemic, looking forward to burning it!
I've settled on 13.0 grains. I load a PB 358156 that we ran as a group buy a few years back.
I realize this is more of a .38-44 load, but I have a K frame .357 and I want it to last forever, which it likely will pushing 158s at @ 1150-1200 fps.
I think the manuals go up to around 14.5 or 15 grains, but I just don't need that. I have a .44 magnum (which, incidentally I do the same thing with. A 250 Keith at 1200 fps will do more than anything I need, and if not, well, I have a .30-06...)
Last edited by Patrick L; 04-07-2020 at 05:26 PM.
My Lyman 358156 of 16-1 alloy fully dressed with BAC lube and Hornady GCs weight 162 gr. Loaded over 14.0 gr Alliant 2400 in W-W cases with WSP primers they push 34 - 35,000 psi (measured with Oehler M43 PBL) depending on lot of powder. They run 1340 fps (muzzle) out of my Ruger SS with 6" barrel. Loading 14.5 or more gr gets a little "dicey"......
Larry Gibson
“Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.”
― Nikola Tesla
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |