where did OLD LEE HAND LOADERS get the name WHACK A MOLE??
where did OLD LEE HAND LOADERS get the name WHACK A MOLE??
It would have been from the carnival game where 'moles' pop up out of holes all over a big table top for a second or so,
and you hit them with a mallet before they go back down.
With the old Lee, the process of using it required whacking the case with a hammer for each step.
In the Service, I had Duty NCO one night and heard what sounded like a shot in the barracks.
I found one of the guys sitting on the floor in his area with a hammer in one hand, a Lee loader die
in the other, and some primers nearby.
He'd been a little over zealous seating one.
Last edited by Winger Ed.; 03-18-2020 at 03:28 PM.
In school: We learn lessons, and are given tests.
In life: We are given tests, and learn lessons.
OK People. Enough of this idle chit-chat.
This ain't your Grandma's sewing circle.
EVERYONE!
Back to your oars. The Captain wants to waterski.
Gets your attention the first time you overload a primer in a Lee Hand Loader. No harm no foul though. Ringing in ears. Dark smudge around whichever hand was holding the seating dowel. Wife and kids to help down off of the ceiling. Other than that, don't try so hard.
If it was easy, anybody could do it.
Set a primer off, no big deal. Just go change undershorts and go back to loading.
And I always thought it was the Tap 'N' Pray.
In school: We learn lessons, and are given tests.
In life: We are given tests, and learn lessons.
OK People. Enough of this idle chit-chat.
This ain't your Grandma's sewing circle.
EVERYONE!
Back to your oars. The Captain wants to waterski.
All of which reinforces my preference for the Mequon unitized tool with the red plastic priming tool. You’ve really got to screw up big time to make a primer go off using one of those.
If you use a small arbor type press for the other steps, the only hammering you do is on the spent primer which is by definition incapable of going off, so the safety factor goes way up. Unfortunately, adding said arbor press increases size and decreases some of the flexibility of the Lee Loader package.
Froggie
"It aint easy being green!"
Frankly, I never heard the “whack-a-mole” designation before I started reading Internet forums. If anybody used such a term in the old magazines, books or instructions, I never came across it.
My first cartridge reloading experience was a Lee Loader in .22 Hornet. I “tapped” rather than “whacked” and still got one primer pop out of every 150 or so loaded. Of course, the shielding setup of the base meant nothing would happen, but I finally got tired of it (and the slow operation), went to a gunshow and bought a Pacific Super Deluxe press and a set of Lachmiller dies (both used).
The odd thing was that the “new” setup took about six months of use before the ammo I was loading got to the accuracy level produced by the Lee Loader.
Kinda my experience as well BentRR, to include the accuracy of loads put up on my first press, a used Lyman Spartan. I think of all the years I used Lee hand loaders I popped one primer. I remember exactly where it happened, on the living room floor of our duplex at 591A N. Fresno, Chandler, Arizona in 1973 when I was stationed at the old Williams AFB. I certainly don't remember popping any more. I still have the Lee 16 bore loader Dad started me on in 1961.
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
My first experience with the "whack-a-mole" Lee loader was in 1964. I was helping a friend make some handloads (literally) for his m-1 carbine. We were outside on a concrete sidewalk and neither of us knew much about it. We were too poor to buy anything else. We missed the part about lubing the cases before sizing and we literally pounded to shreds his little hammer with the hard plastic ends. It was a terrible amount of work and our quality from load to load was probably not too good. Looking back on it, its a wonder I took to the reloading bug the way I did. But I remember it was fun and we were very slow but got enjoyment out of it.
Mark 5:34 And He said to her (Jesus speaking), "Daughter, your faith has made you well. Go in peace and be healed of your affliction."
Started in the mid-60’s with a 12 gauge Lee kit, never set off a primer with it, probably because the shot-shell primers were not as easy to crush. I learned a couple years later on a 38 special Lee Loader that a supple leather left hand glove was a good accessory for priming and salvaging live primers from pull down brass.
I like Lee Loaders. I started using one in '69 and even though I now have 3 presses, 13 die sets and 1.32 tons of assorted reloading tools I still occasionally get one of my 7 Lee Loaders out and pound out a few handloads (38 was my first and still my favorite). I had to change skivvies once too often when pounding out some 44 Magnums so I searched for a remedy for the unscheduled/surprising primer pops. I started chamfering the primer pockets just like I did for military crimped primer pockets and made sure the spring and plate in the priming base were free and clear. IIRC the last primer pop I had was around 1980 (?). When priming 38 Specials with the Lee Loader I can't remember any pops, but sometimes I'll use an HF arbor press although I prefer a dead blow hammer...
For those not familiar with a Lee Loader (and those that think they are "slow"); https://www.youtube.com/watch?v=UeEl9wZyabc
My Anchor is holding fast!
Never heard that term until right now. I have one in .44-40, never used it.
My Dad absolutely Hated them. Said the only thing that Lee made that was worth anything was the decapping base & rod.
Back in 1974 when I was stationed at Bethesda, I wrote him that I had just bought a 1903A3 & S&W K-Frame .38Spl with Lee loaders, Wrote back immediately and ordered me NOT to use them. He was sending Lyman 310 Tong Tools & a scale. At least I wasn't making noise. Except for the decapping, I used my shoe as a hammer while I waited for the Tong Tools to arrive.
I HATE auto-correct
Happiness is a Warm GUN & more ammo to shoot in it.
My Experience and My Opinion, are just that, Mine.
SASS #375 Life
"In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'
The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery
NRA Benefactor 2008
You've never played the arcade game " Whac-A-Mole" man that was my favorite one....it was FUN!
It was created in 1976 by Aaron Fechter who worked for Creative Engineering .
Plastic moles popped up & down out of holes and if you could hit them fast enough and hard enough with a soft black plastic mallet...you got points .
Since the Lee Classic Loader involved hitting the case with a plastic mallet to drive it in...Whack-a-Mole sounded funnier and was easier to spell than Lee Classic Loader... We like funny names like boolit !
I can honestly say I've whacked many a mole !
Gary
Certified Cajun
Proud Member of The Basket of Deplorables
" Let's Go Brandon !"
A Lee Loader in .38 Special was my introduction to reloading, clear back in the stone age times of 1969 or so. The price was a whopping $9.95, brand new, which was my limit at $99/week paycheck. I read the instructions carefully and deprimed all the cases. I then began the priming process, ever so gently urging each one into place with moderate hammer taps. I think I got about ten done and thought "I don't like this. Not at all".
I went back to the same store and bought a used C press and used .38 Special dies. And a reloading legend was born............... Oh, I gave the Lee away.
I'm like Typhoid Mary. Although I have several many of those kits around, I seldom use them. However I inspire others to use them and they seem totally happy with their results. It's like they get infected, but I'm immune. Interesting concept, huh?
Froggie
"It aint easy being green!"
Chuck E. Cheese pizza and game parlors had "whack a mole" games about 35 years ago.
EDG
I've actually had really good luck with the Lee Smack-N-Shoot kits. I haven't used mine in a while, but methinks I might take it to the range next trip to show it off.
MC-130J Driver
Former T-6A Texan II Driver
FAIP Mafia
Hook 'em all
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |