Words are weapons sharper than knives - INXS
The pen is mightier than the sword - Edward Bulwer-Lytton
The tongue is mightier than the blade - Euripides
swaging reduces the diameter doesn't it? Texas seems right to me too.
Swaging is pressing the lead into a mold of some shape. Can be any shape or dia you want.
If you swage a round ball you can simply flatten the end of it until it makes a short cylinder with a round nose. It will be shorter than a round ball of the same weight.
Or, as stated above, you could use a hollow point front end and flat back end, or any other shape you want, including a hollow base. Just have to use the proper dies.
Most do not swage lead simply due to the cost of the dies.
Sent from my SM-P613 using Tapatalk
This online calculator seems to work -
https://www.vcalc.com/wiki/vcalc/sphere+-+weight
However, it uses the ball's RADIUS, which is simply half of the diameter.
The blue fields allow you to select the units you want. For example, a .45 ball has a radius of 0.225 inches, and pure lead has a density of 11.3 g/cm^3.
The calculator output is set to "grain", and the weight is 136 grains.
"Commerce with all nations, alliance with none, should be our motto."
- Thomas Jefferson
Hi, I will release a calculator soon that will include calculating round ball bullet weight. (I will include link in this post)
So, I have converted the code from Visual Basic to Javascript. This way it will be a web based calculator.
Link to get it running is here: https://weatherby.dk/BP/rb/roundball.htm
Looks like this: (Will be upgraded)
Enjoy!
Last edited by Lars-K; 05-03-2023 at 05:22 PM.
I once wrote an equation on my trusty HP28 calculator for calculating the number of shot in a shotshell for a given shot size and payload.
The HP had a function called "Solver", and the beauty of it was that you could have any number of variables and the calculator would solve for each of them as long as the other variables were filled in.
The program had four variables:
#1 = Diameter of shot
#1 = Weight of shot
#2 = Number of pellets
#3 = Weight of payload
#4 = Density of shot (this variable was a switch between two values. I use the density for lead and steel)
If you input two of the first three variables, the program would calculate the last:
If you wanted to find the weight of a single ball, you just filled in the diameter and "1" for number of pellets.
If you wanted to find the size of the balls in a 1-1/8 ounce 12 pellet buckshot load, you entered "12" for pellets and 32 for weight (32 grams=1-1/8 ounce)
And finally, to find the number of shots, fill in payload weight and pellet diameter.
These days, I use the ballistic program KPY https://kpyshotshellballistics.com/ It has many nice features, and I can strongly recommended it
(the link gives an privacy/security warning, but is alright)
Cap'n Morgan
I have a LEE double cavity .495 mold ---the formula says 182 grains -- weighed a run of stuff this morning got from 181.5 to 183.2 - - I am some perticular with the look of my cast stuff . no wrinkles etc so any junk ones went back in the pot.
After casting I tumble these in a canvas bag with some powdered graphite and I load with sprue every whichaway (cant see it after the rumble / tumble).
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |