Lee PrecisionInline FabricationADvertise hereRotoMetals2
Titan ReloadingRepackboxWideners

Page 2 of 2 FirstFirst 12
Results 21 to 25 of 25

Thread: Sore fingers

  1. #21
    Boolit Buddy
    Join Date
    Feb 2016
    Location
    S.E. Michigan
    Posts
    212
    Quote Originally Posted by Andyt591 View Post
    I'm not 100% certain that this is the right place for this, but...

    My fingers are a bit sore today. I sized all of my 30-30 cases. Then I hand trimmed them (no machine, just a hand tool). Next I deburred 100 of them and used my RCBS universal hand primer to install the primers. Tomorrow night (or sometime this weekend) I plan on loading them. Wish me luck because this is my first solo batch of cartridges using my own equipment. I'm trying to decide on a starting powder charge right now. It might take me a couple of days but I think I'm going to end up settling on 28.3 gn of powder. It's a little towards the high end of the middle of the minimum and maximum. IMR 4895 w/ Sierra 150 gn round nose bullets.

    Attachment 253730
    I started out with the same tools and the same cartridge the good ol 30 wcf. I had so many blisters from that hand trimming tool. I would have to wear carving thumb protectors because I was processing 250 pieces of brass. One hint though. You don't have to trim your brass as long as it's not over the max brass length. The max brass length is much different than the trim to lengths the reloading manuals tell us to trim our brass too.

    Once I learned that, my fingers healed up very quick.

    So for the 30-30 the max brass length is 2.039

    The trim length from the book is 2.029. Personally I only trim anything over 2.040 and i trim it down to 2.040.

  2. #22
    Boolit Master
    Tom W.'s Avatar
    Join Date
    Mar 2005
    Location
    Phenix City, Alabama
    Posts
    3,846
    I turned mine into an A.I. and haven't had to trim since!!!!!
    Tom
    μολὼν λαβέ


    Did I ever mention that I hate to trim brass?

  3. #23
    Boolit Buddy
    Join Date
    May 2012
    Location
    South Texas
    Posts
    311
    I would use a cast bullet!

  4. #24
    Boolit Buddy gumbo333's Avatar
    Join Date
    Apr 2015
    Location
    NE by the Mighty Mo
    Posts
    146
    My 30/30 brass has never grown much to need trimming. Even the 170 gr Speer's loaded with LVR. But my most accurate loading is not the fastest as listed in the manuals. That's a plus for lever action or lower pressure type cartridges.

  5. #25
    Boolit Master
    Join Date
    Feb 2011
    Location
    SE Kentucky
    Posts
    592
    My trimmer is an old Forster with the handle that screws on and removing the handle let me chuck it into a battery drill. The Lyman hand tool is nice but cutting about 1 1/2 inches off the tip end of a scrap cleaning rod lets you screw the various chamfer tool into it and then chuck the rod in the drill and go for it. Not sure what you use for trimming but the Lyman trimmer has a power tool attachment that will let you use a drill.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check