Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
The tighter group has a patch thats .080 longer than the larger group
Sent from my iPhone using Tapatalk
Interesting. I really need to test some lengths on my patches. So far it's been guess and go.
Sent from my E6910 using Tapatalk
Where did you put the extra .080? More tail? More ogive?
The only amendment the Democrats support is the 5th.
I made them taller and closer to the ogive.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I must say, the common wisdom is to patch no farther up the boolit than the ogive but some patched boolits I was given with a mold were patched way past and shot remarkably well.
I wonder if a tiny bit of patch past the ogive makes for a quicker patch release.
ian, can you show me the base of those two bullets in the same order?
Those bullets have been shot buy now but they are similar to this one
Sent from my iPhone using Tapatalk
Love those work boots !
Good Judgment comes from Experience, Experience comes from Bad Judgment !
ian
The reason I asked was, if you raised the patch higher on the ogive that you might have exposed more of the base. But what you show there looks good.
I find keeping the patch right at the transition of the shank and the radius is where I get the best accuracy, but I see a difference in accuracy when the whole base of the bullet is covered, it falls off.
Those small dimples are right at the end of the shank where I hold the patch.
The thing is getting the alloy balanced so the bullet does not have to much obturation that the land cuts cut bare lead ahead of the patch destroying the accuracy.
Attachment 248245
Here are three bullets with different hardnesses. The first is good the second is almost to soft and the third is to hard and the chance that it will loose rotation.
Attachment 248246
When I patched up the bullet farther I made the patches longer to make up for it. I still might make them just a tad longer still. I am going to shoot the Shiloh into the pool tomorrow so we will see what happens and go from there
Sent from my iPhone using Tapatalk
Ian with the scores you shot at Atterbury, I don't think changing anything would be a good idea.
Long range rules, the rest drool.
Yea your right. I will still shoot it into the pool so that I will know what the bullet looks like when its working properly at least
Sent from my iPhone using Tapatalk
. I will make a new thread this evening with more detailed notes of what all we tested but here are some more boolits that were shot into the pool. The bullet on the right was shot out of my c sharps highwall and the 2 on the left were out of the Shiloh. Like I suspected the Shiloh with its tighter bore was bumping up further than the highwall. We made the patches for the Shiloh another .040 long. Interesting to note before we started shooting the Shiloh I went to clean the oils out of it like usual and good bit of lead came out. So it looks like the .080 longer patches still are not long enough. We shot a few patches that were .040-.050 longer than the long patches that were shot previous and there was absolutely no leading. We also experimented on how much overlap on the base of the bullet was to much and that does seem to make a difference. The less overlap the better the bases seemed to be. Ill up load some more pictures and the results of yesterdays testing this evening.
Sent from my iPhone using Tapatalk
Any more testing on your patches ? I wanted to get a bunch of different patch configurations tested but too many obstacles so far. My patches with more overlap seemed to perform better at long range yesterday, but had other issues going on so wasnt a good test.
Sent from my E6910 using Tapatalk
Were these fired into the pool at full load?
This picture and the previous one with the three different alloy harnesses makes me think that nose slump may not be a real thing.
Surely it would show up shooting into a pool!
An optical comparator would sure be nice to look at the pre and post fired boolits.
They were fired into the pool at full load. The nose bump up on the softer bullets is much more pronounced. Maybe instead of calling it nose slump a more correct term would be nose setback
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Man at the variables we have to deal with to make these shoot! It's great to see the results from bullets that haven't been dug out of a berm.
What was your alloy for the "softer bullets"?
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |