Titan ReloadingRotoMetals2Inline FabricationLee Precision
MidSouth Shooters SupplyRepackboxADvertise here

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Results 1 to 5 of 5

Thread: does anyone make an automated gas check maker that is available on the market

  1. #1
    Boolit Bub
    Join Date
    Mar 2008
    Location
    rapid city sd
    Posts
    38

    does anyone make an automated gas check maker that is available on the market

    i am of the belief go big or go home, and would like to find an automated gas check maker, i know the big boys have them them but have yet to find who makes them,,, i think they engineer their own, does anyone know of a manufacturer of one that is open to sale to public or business, thanks for any info

  2. #2
    Boolit Master



    skeettx's Avatar
    Join Date
    Jul 2009
    Location
    Amarillo, Texas
    Posts
    3,091
    NO

    Closest I got was
    https://www.amazon.com/Ton-Electric-.../dp/B078MCN6DX

    and no feed on it

    Mike
    NRA Benefactor 2004 USAF RET 1971-95

  3. #3
    Boolit Master Idz's Avatar
    Join Date
    May 2013
    Location
    New Mexico
    Posts
    625
    If you make your own press mounted dies you can make a hundred checks in few minutes. Unless you're going into business that should be a good enough production rate.

  4. #4
    Boolit Master Handloader109's Avatar
    Join Date
    Jan 2014
    Location
    NW Arkansas
    Posts
    1,455
    There was a member about 2 years ago that had automated his setup. I got some 22 caliber aluminum from him at the time. I looked last year for him and he hadn't posted in a while.
    You might can do search and locate the posts.. He was kicking out about one or two a second.....

  5. #5
    Boolit Buddy
    Join Date
    Aug 2011
    Location
    The Netherlands Europa
    Posts
    147
    Make sure your feed is in line with your stroke on a simple arbor press.
    So a simple electric 12v dc rc motor with a polie and coil guidance, a simple pneumatic cylinder with compressor, some electronics based on a 555 clock ic, wil do the trick.
    Every second a gs.
    Make sure when you are going to test, you build in some room to get a bigger or smaller poelie for feeding so you can adjust how much the coil will travel into your die.

    The cylinder and the compressor will be the most expensive part.
    The cylinder and compressor can also be used on your lube sizer for continuous lube pressure.

    Instead you can also go for arduino to "program" the time, very handy for measuring powder in a 505 scale with a tricler.
    They laser (eye) will watch when the needle is at zero and will stop the trickler.
    Have fun

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check