MidSouth Shooters SupplyWidenersInline FabricationLee Precision
ADvertise hereTitan ReloadingRepackboxRotoMetals2

Donate Now Goal amount for this year: 6000 USD, Received: 6135 USD (102%)
OUR GOAL HAS BEEN MET!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Page 2 of 2 FirstFirst 12
Results 21 to 25 of 25

Thread: HG #38 Ness Safety Bullet

  1. #21
    Boolit Master
    Join Date
    Jul 2009
    Posts
    614
    IIRC, I read in some "long ago and faraway" thread that some folks would put a dab of hot lead on the base of the pins (perhaps after the sprue has solidified?) to keep the pins hot. Seems to have worked for them... I haven't tried it yet, though. Just a thought.

  2. #22
    Boolit Buddy OldBearHair's Avatar
    Join Date
    Jul 2014
    Location
    Conroe TEXAS
    Posts
    428
    Anyone try WD40? It seems to work on nearly everything!

  3. #23
    Boolit Master gpidaho's Avatar
    Join Date
    May 2014
    Location
    Beautiful Idaho
    Posts
    1,855
    Coat the pins lightly with dielectric silicon grease. Works for me. Gp

  4. #24
    Boolit Buddy
    Join Date
    Mar 2018
    Location
    Sioux Falls, SD
    Posts
    198
    I polished my pins and graphited them and took another run at this mold yesterday. Preheated the mold on a hotplate. I set the PID at 750 the first few had terrible fill out, but dropped right off the pins, I cast for a while, but kept getting wrinkled bullets. I ran the pot all the way up to 800, but still wrinkled bullets, and no frosting, I did get some flashing, tho. It seemed like the faster/hotter I cast, the worse they stuck. I then tried turning the pot down to 700 but still kept getting wrinkled bullets, but less sticking. I'll cull tonight, but I dont expect to find many, if any, perfect bullets. I might be hard pressed to find many useable ones.

    is it possible that hotter = sticky pins?

  5. #25
    Boolit Master
    barrabruce's Avatar
    Join Date
    Feb 2009
    Location
    Far Nth Qld Australia
    Posts
    1,383
    Itís been all deaths ,births and marriages Ďround hear, so I havenít had time to wrestle with the beast for a while.
    But when I get wrinklies and Iím good and hot and should fill out but donít.
    I pour a little pure alcohol in the mold and let it bubble and spit for a bit then tip the rest out.
    Seems to get rid of the oil residue etc which usually helps.
    Works for me.

    Ohhh!
    Donít blame me if you tip the boiling vaporising spirit into a fire or hot molten lead.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check