This is another neat mold running on another forum with 11 takers so far. Perhaps it will gain better traction over here. I personally must have a couple for myself.
Here is the link: http://singleactions.proboards.com/t...et-mold-design
Here is the description, pay attention because of the size of the bullets these are made on the 2 cavity molds with 3 cavities instead of 2 so read the description carefully as there are several options!
MiHec 227640 Hornet 3 Cavity Brass Cramer Plain Base or Gas Check mold Hollow Point mold.
This is a new boolit design that was inspired by several people here. This will be suitable for any 22 caliber firearm, but is specifically for commercial rifles and handguns. It will cast at about 0.227" dependent on your alloy and easily sizes smaller. The weight is as shown on the drawing dependent on your alloy of choice.
We will need fifteen (at least) to commit to this. We will run this until we get the number we need (probably 34 HP molds due to current supply conditions) or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
I am offering these choices: 3 cavity PBHP, 3 cavity GCHP, 4 cavity PB solid, 4 cavity GC solid. These are on MiHec's two cavity brass blocks.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Here is the pricing via Miha:
6 cavity solids on 4 cavity brass blocks (95 euros shipped full price) - 80,75 euros with 15% off
4 cavity solids on two cavity brass blocks (80 euros shipped full price) - 68 euros with 15% off
3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
3 Cavity Plain Base
01. paska_10 ÄT hotmail doT com....1 mold
02. eagle-rainATcoxDOTnet....1 mold
03. bad22inc aT gmAil doT CoM....1 mold
04. fireman dot webb@gmail dot com....1 mold (with one set of handles)
05. vfluckey at midco dot net....1 mold
06. aaronpetroski at gmail dot com....1 mold
07. ckulyk AT telus DOT net....1 mold
3 Cavity Gas Check
01. willam dot kinderknecht AT gmail DOT com....1 mold
02. vfluckey at midco dot net....1 mold
03. ramsbooty at gmail dot com....1 mold
04. rockyert68 at yahoo dot com....1 mold
05. greggoryashley at yahoo dot com....1 mold
06. gnslgr1911 AT yahoo DOT com.....1 mold
07. ieharm AT hotmail DOT com.....1 mold
08. jadepump at pldi dot net....1 mold
09.
10. mstreddy at gmail dot com....1 mold
11. jixxerbill64 at yahoo dot com....1 mold
12. thaine AT yucca DOT net....1 mold
13. ringram3 AT gmail DOT com....1 mold
14. goodfarms1 AT frontier DOT com...1 mold
15.
4 Cavity Gas Check Solid
01. jbillwelch at yahoo dot com....1 mold
02. Renegado at twc dot com....1 mold
03. panshovel AT live DOT com....1 mold
04. brassmagnet at iCloud dot com....1 mold
05. cuffem4 at centurytel dot net....1 mold
06. Dschuttig AT yahoo DOT com....1 mold
4 Cavity Plain Base Solid
01. brassmagnet at iCloud dot com....1 mold
6 Cavity Plain Base Solid
01. colt38sp at gmail dot com....1 mold