NOTICE: This mold is on MIHA's to do list. I don't know exactly when it will close but you should go ahead and sign up if you are wanting one. Also, it helps me a great deal if you can use this format to sight up as all I have to do is cut and paste: bigtimeshooter AT hotrange DOT com Thanks to everyone for their patience and courtesy.
This one is running strong already on another forum with 28 takers. It has been running since 050518 so hopefully we should see some action from Miha on it soon. On the other hand it might still be some time. While I think it has enough takers already to take it directly to the group buy section I want to be dead sure you guys would like to see this one so as not to clutter that area necessarily. Here is the link so you can see the drawing: http://singleactions.proboards.com/t...640-new-designMiHec 3 Cavity Brass Cramer Plain Base or Gas Check mold or 6 Cavity solid mold.
This is a new boolit design. This will be suitable for any .257 caliber firearm. It will cast at about 73 grains dependent on your alloy.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Cup HP pin, and 3) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Pricing updated via Miha
6 cavity solids on 4 cavity brass blocks (95 euros shipped full price) - 80,75 euros with 15% off
4 cavity solids on two cavity brass blocks (80 euros shipped full price) - 68 euros with 15% off
3 cavity cramer HP's on two cavity brass blocks (110 euros shipped full price) - 93,5 euros with 15% off
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Post your disguised e-mail address imashooter AT gmail DOT com, mold choice (3 or 6 cavity), base style (PB or GC) and number of molds wanted (one to however many).
3 cavity GC list
01. gnslgr1911 AT yahoo DOT com....1 mold
02. Sethdoty 444 at g mail dot com....1 mold
03. ChuckV cvcooks AT gmail dot com....1 mold
04. jsczurek AT yahoo DOT com....1 mold
05. gspatton at gttransmissions dot com....1 mold
06. mhkilgore AT mac DOT com....1 mold (MUST BE .260" Diameter)
07. victory AT vermontel DOT net....1 mold (MUST BE .260" Diameter)
08. jstahlconstruction at yahoo dot com....1 mold
3 cavity PB
01. paska_10 At hotmail Dot com....1 mold (PREFERS .260" Diameter)
02. eagle-rain AT cox DOT net....1 mold
03. Badwolf.db AT gmail DOT com....1 mold
04. ChuckV cvcooks AT gmail dot com....1 mold
05. gspatton at gttransmissions dot com....1 mold
4 Cavity Solid Plain Base
01. Seth Doty 444 at Gmail dot com....1 mold
6 cavity Plain Base BRASS mold
01. gspatton at gttransmissions dot com....1 mold
02. mhkilgore AT mac DOT com....1 mold (MUST BE .260" Diameter)