WTS: MP Molds

[Echd]

Trying to sort through some of the stuff I don't use much. Aside from some of the more collectible oddity molds, I'm finding more of the ones I don't use to just be clutter.

First up is a 180gr LFN 4 cav brass 357 mold, marked as 358-180RF. This mold has never been cast with. Other than some very slight rust freckling on the top bolt, it's brand new. You can thank Hurricane Florence for that one (along with other rust spots my mold collection picked up during the near-week without any power...) Comes with all pins. $115 shipped. SPF



Second is an Oreo .40 caliber 200gr mold for the 10mm. I bought this used about 2 years ago and have yet to cast with it once (or to buy a 10mm) so I think it's safe to put it on the chopping block. I also traded all my 10mm brass, so there's that too. Comes with all pins- HP, cup, and flat. It is used and shows the standard discoloration, but as I said, I haven't used it personally. $105 Shipped.



Third is a 358-429 HP 2 cav. This is from an earlier run that had an incorrectly cut driving band, so you actually get two sets of blocks with this mold- one with full groove driving bands, and one with a slightly smaller front band. I'm given to believe the former is more "authentic" to the original keith, whereas the latter is the current and more modern incarnation. I now have a 4 cav from a later run, so I have no use for this. I have not used this mold and it appears unused. Has all pins. $90 Shipped. NOW $85 SHIPPED



Fourth, a six cavity 356-130 slick sided mold, good for hitek or powdercoat. Shoots quite well but I'm more into heavier suppressed 9mms nowadays so this doesn't see much use. This is a little dirty with some freckles on the hardware but will still sling a perfect slug. With a bevel base and the slick sides, you won't find a faster casting brass mold. $65 shipped. SPF



I heavily prefer paypal and I'm not really looking for trades, but you can try me- just don't be surprised when I turn you down. Looking more to free up some pocket change to do some work on my range.

[pacomdiver]

Fourth, a six cavity 356-130 slick sided mold, good for hitek or powdercoat. Shoots quite well but I'm more into heavier suppressed 9mms nowadays so this doesn't see much use. This is a little dirty with some freckles on the hardware but will still sling a perfect slug. With a bevel base and the slick sides, you won't find a faster casting brass mold. $65 shipped.

ill take it, pm for payment info

ETA :Payment sent

[pettypace]

First up is a 180gr LFN 4 cav brass 357 mold, marked as 358-180RF.

I'll take it. Please PM you paypal address

[Onebad06vtx]

I will take the 40 cal mold
PM me your paypal address

[NikA]

On the off chance that the .40 cal mold deal falls through, I will take seconds on it.

[Onebad06vtx]

I paid paypal for the 40cal mold

[Onebad06vtx]

I paid with paypal for the 40 cal mold

[cwlongshot]

Darn it!! I it missed another one!

Good luck with remaining sales!!

CW

[Echd]

Just the 358429 left. Bump.

[Echd]

Bump with one price drop.

[Handloader109]

pm sent on the 358-429

[pettypace]

pm sent on the 358-429

I assume Handloader109 will take the 358-429. If not, I'll take it.

[Echd]

I actually have not received a PM from handloader yet, so it is still fair game. Shoot me a PM if you want it.

[Handloader109]

Hmmm, I actually sent PM prior to replying here...
Oh well.
Your choice. I'll not be upset either way I didn't say I'd take it here and I should have.

Sent from my SM-G892A using Tapatalk

[Echd]

You might want to check your sent messages. I have not received one from you and perhaps you sent it to another party by mistake.

[Handloader109]

AH, I sent email....... wrong button. But sell to Pettypace if he wants it....

[Echd]

It is still available, just give the word. Sending it to an email instead of a PM is a pretty innocuous mistake. You're free to pass of course but as Pettypace qualified his interest around yours, I think he would be gracious enough to let it go if you still wanted it.

Side note, I don't know if this site's email function works- I have the correct email in my profile but have never received an email from this site so far as I can recall.

[pettypace]

You're free to pass of course but as Pettypace qualified his interest around yours, I think he would be gracious enough to let it go if you still wanted it.

Exactly. Just wanted to express interest in case Handloader109 declines.

[Handloader109]

Well, I'll take it......

Sent from my SM-G892A using Tapatalk

[Echd]

Sold.