CLOSED:MiHec - RERUN 45 RUGER ONLY HEAVY WEIGHT 640 DESIGN CRAMER HP

[Wasalmonslayer]

MiHec - 2 or 4 cavity brass Cramer HP or 4 Cav Brass/6 cavity aluminum solid either plain base or gas check

This is about the fourth rerun of this design. This will be a two or four cavity cramer brass HP or 6 cavity aluminum solid mold in either plain base or gas check. Choose your diameter either .452 or .454
It fits the Ruger Single Action Blackhawk cylinder length. The meplat to crimp groove measurement is 0.456".


We will need 100 total hp pins to get into last call on this one. We will run this until we get the number we need or until the GB closes.

If the HP pins are not suitable for reversal to a solid, the blank pins come with the price of the mold. If you do not want the HP pin sticking out of the base of the mold, in the case of reversable pins, you can order a set of blank pins for a smooth mold bottom.

Pin options: 1) large HP, 2) penta HP, 3) small HP, 4) cup HP, 5) blank pin for flat nose

Weights for various options: Solid = 327 gr., large/penta hp = 299 gr., small hp = 311 gr., cup hp = 321 gr.

Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec. Invoices will be sent out via e-mail from the listed addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars. After you pay, the mold gets shipped.

Prices are -

- 2 Cavity HP all pins included 95 Euro's (80,75 with discount)
- 4 Cavity HP all pins included 135 Euro's (114,75 with discount)

- 4 Cavity solid Brass 95 Euro's (80,75 with discount)
- 6 Cavity solid Aluminum 95 Euro's (80,75 with discount)


Please list your Forum name and your disguised e-mail address in suitable form, the base type wanted... either plain base or gas check, the pin options you think you want and the number of molds you want.

Here is a look at what we are running -

[Wasalmonslayer]

Sign up Thread -

HP Design -

1) spero 64 at g mail dot com - 2 Cav GC
2) krott AT tds DOT net - 4 Cav PB
3) gspatton AT gttransmissions DOT com -4 Cav PB
4)
5)

Solid Design -

1)
2)
3)
4)
5)

[Wasalmonslayer]

Friday bump

[Greg S]

Put me down for a 2 Cavity GC wit all da pins. gp spero 64 at g mail dot com. 98 pins 2 go, 98 pins to go, ya take one down pass it around.....

[Wasalmonslayer]

Put me down for a 2 Cavity GC wit all da pins. gp spero 64 at g mail dot com. 98 pins 2 go, 98 pins to go, ya take one down pass it around.....

Thank you sir for breaking the ice

[jaydub in wi]

I would like a 4 cav HP PB with all the pins. krott AT tds DOT net
thanks

[Wasalmonslayer]

I would like a 4 cav HP PB with all the pins. krott AT tds DOT net
thanks

Thank you got you added!

[gtgeorge]

gspatton AT gttransmissions DOT com - .454 HP PB , all pins

[Wasalmonslayer]

gspatton AT gttransmissions DOT com - .454 HP PB , all pins

Got you added

Thank you!

[Wasalmonslayer]

Bump it up

[Lefty SRH]

Why did the group buy close so fast? Only three are signed up and its only been posted for a month.