I have a brand new Rossi 92, 44mag, that is causing case separation about one half inch from the rim. The bolt will close on a .016 shim but not on .020 shim. Is that excessive head space, and in turn causing the separation?
I have a brand new Rossi 92, 44mag, that is causing case separation about one half inch from the rim. The bolt will close on a .016 shim but not on .020 shim. Is that excessive head space, and in turn causing the separation?
The rim thickness spec. for a .44 Mag. is .06". That is considerably more than your shim thicknesses, so given the information you have provided I would say that headspace is unlikely to be the culprit. I'd like a detailed description of your shims and how they were used. I'd also like to know about your ammo -- factory loads? Reloads? New brass? Old brass? Yours is the second recent post about case separations in the Rossi R-92 .44 Mag. I have one and have experienced no problems. I'm using reloads, but started with new Starline brass. One poster stated that he could observe a ring in his chamber. What does your carbine's chamber look like? Are your loads excessively hot? There is a certain "springiness" to lever actions, and a hot load might be enough to develop headspace issues with a carbine that had marginally good headspace. We'll probably be better able to offer conjecture about your problem with more information.
Do you mean it will close with a .016 shim along with the brass casing. If so that is excessive for any gun.
Jedman
I was one of the previous posts, the ring in the chamber was caused by several case ruptures. I cut round shims from a pop can each .004 thick one ar a time placed them on the back of a case and closed the bolt. I could close the bolt on four but not on five. This tells me I have more than .016 of headspace above what is required to chamber the round. I think that is too much, loads were mild you might not get separation with factory loads but I would hesitate to use those cases again if that headspace is excessive.
This is interesting, I’ll follow this thread for my education
8500' Wet Mountain Valley, Colorado
Case head separation is caused by the same thing regardless of the method of actual headspacing. The firing pin pushes the case forward and the thinner part of the case expands to seal the chamber. As the pressure increase the case head moves back to the breech or bolt face and since the thinner mouth portion will have more friction due to its thinner walls the case stretches.
For any bottlenecked cases that have rims or belts best practice is to set you dies for your shoulder clearance same as rimless bottleneck cases.
Last edited by M-Tecs; 04-10-2019 at 12:42 AM.
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when your reject something you don't know anything about".
- Wayne Dyer
Head space should be .002- .004". On low pressure cartridges the primer will back out. Depending on wall thickness of the brass the pressure can very on which loads will have head separation or not. Cartridges like the 30-30 ( 42,000 psi ) will usually back the primer out. The 44 mag at 36,000 has thinner brass and can separate the head. I had a 454 with about .008" headspace that separated a few weeks back. I usually use masking tape to check head space on old guns, had a 94 a few years back that had .025" head space and was still being used. It would back the primers out and thats how the head space was measured.
M-Tecs, do you really believe that .016 inch clearance in the head space on 44 magnum will cause case separation?
On the first firing of the brass no but with repeated loadings yes. That being said I have never worked on a 44 magnum with this issue. I have set the barrels back a Martini Cadet in .38 special, a 45 Colt in a Winchester 94 and a couple of 45-70's that separated cases due to headspace issues.
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when your reject something you don't know anything about".
- Wayne Dyer
Your rifle needs to go back to the factory, or to a warranty repair station.
I had a Mosin Nagant made in 1896 that had a headspace issue.
There was .012" clearance between the case head and the bolt face.
Sometimes they would split the cases when using steel cased ammo.
But the Brass cases stretched.
I would just neck size them, ( Norma cases ) and reload them.
I was able to get over 20 reloads out of the once fired cases before the necks started to crack.
Finally I decided to Silver Solder a .010" Feeler gauge Shim onto the bolt face to take up the extra headspace since I could not find a bolt head replacement that closed up the headspace.
And no gunsmiths in my area wanted to remove the barrel and set the barrel back because the chamber reamers were not available at that time.
That was in the early '70's and I hadn't bought a lathe yet.
I sold that rifle to a friend, who sold it to a friend, and he still has it and is shooting it to this day with Steel Cased ammo with no problems.
Rimmed cases are way more forgiving than Straight Rimless bottleneck calibers.
Both owners of the rifle were Fully aware of the modifications that I had made to the bolt face and the possible headspace issues.
They didn't care because at that time, the Nagant was not a popular shooter.
I know the current owner has shot up an entire 440 round Spam Can of surplus ammo with no issues.
Last edited by LAGS; 04-10-2019 at 11:44 AM.
No clue as to steel handles excessive headspace. With brass cases as long as the case head is held against the bolt or breech face the fireforming process does not show any internal head separation signs when you are blowing the shoulder forward for wildcats. Best is to form a false shoulder but jamming the bullet into the lands works well also.
A while back a buddy inherited a 60's vintage custom rifle in 257 Robert Ackley Improved. The woodwork and blueing was as nice as I have ever seen. The chamber not so much. It was cut .030" deep. I agreed to set the barrel back, however, after seeing that the blueing was flatout gorgeous I was worried about damaging the finish. Showed him how to properly fireform the brass using jammed bullets and set his die for a .002" shoulder setback. Not truly an AI anymore but treated as a wildcat it works well. He hasn't had an issues with it in 15 years. Case life went from 2 or 3 loadings to over 20.
Last edited by M-Tecs; 04-10-2019 at 12:36 AM.
2nd Amendment of the U.S. Constitution. - "A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."
"Before you argue with someone, ask yourself, is that person even mentally mature enough to grasp the concept of different perspectives? Because if not, there’s absolutely no point."
– Amber Veal
"The Highest form of ignorance is when your reject something you don't know anything about".
- Wayne Dyer
I was the one with an actual step or ring of sorts in the 44 rifle chamber that was tearing my cases in half, I lapped it with sandpaper. I don't know how long my cases will last now but it was about a year ago I did that and ive still never seen any type of damage on cases
I would fire a few factory loads through the rifle and if needed section the cases and look for a thin spot to eliminate hand loads from the problem and include them when returning the rifle .
Or if you or a gun smith determines it has a headspace problem and has not been modified in a way that could cause the problem I would return it and let them fix it.
It’s a new rifle give them the opportunity to make it right.
On most centerfire firearms a simple test for headspace is to take a sized and primed casing , not a loaded cartridge and fire it in your gun. When you get the brass out of the gun look at the primer if your gun has excessive headspace you will see the primer has backed out and no longer flush or below flush to the back of the brass as before firing.
There are some firearms that have a extractor or ejector that can hold the cartridge tight enough to the bolt face that this test may not show the correct issue but for most guns this test will show you if you have a headspace problem, bottle necked or strait walled both.
Jedman
julian hatcher experimented with headspace in 1919 belt-fed autos chambered in 30-06 and determined that case head separation begins at 15 thou and is consistent at 25 thou in that combination.
he was cheif ordnance officer at the time.
If you can feel the primer above the surface of the casing it's probably at least .005 and that is probably OK but if it's .010 or more it's too much.
Jedman
I took the 92 back to the range, fired 10 rounds, they functioned great but I could see a faint ring on one and could feel it from the inside. One other had a distinct ring you could feel with a thumb nail on the outside, and with a wire on the inside. I now have no doubt excessive headspace is the problem, and will send it back.
I hope they get it fixed for you.
I have had to return several new guns back for repair mostly Rugers also Springfield ,Glock , Kel-tec but I keep buying cause I like um all , but have found it wise to run a few boxes of ammo through any new gun before sights or any other kind of upgrade.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |