Titan ReloadingWidenersReloading EverythingMidSouth Shooters Supply
Lee PrecisionLoad DataInline FabricationRotoMetals2
Repackbox
Results 1 to 15 of 15

Thread: Graf 30-40 brass

  1. #1
    Moderator
    Texas by God's Avatar
    Join Date
    Mar 2016
    Location
    Texas
    Posts
    14,335

    Graf 30-40 brass

    Has anyone tried these? Thanks in advance.

    Sent from my SAMSUNG-SM-G930A using Tapatalk

  2. #2
    Boolit Grand Master


    swheeler's Avatar
    Join Date
    Mar 2005
    Location
    Montana
    Posts
    5,471
    Not yet, but if like the rest of their brass it will be good stuff. In 2006 Win did a run and I bought a 100, still using them.

    OOPS! I just went and looked at Graf's their 30/40 brass is made in USA, I figured Privi/PPU/NNY stuff they usually put their name on, or not some times. I've gotten Graf brass with their name and NNY plus PPU head stamps all sold as Grafs. Sorry my mistake

    and yes I know..........PPU and NNY are all Privi brass
    Last edited by swheeler; 02-02-2019 at 02:52 PM.
    Charter Member #148

  3. #3
    Boolit Master

    pworley1's Avatar
    Join Date
    Dec 2013
    Location
    Mississippi
    Posts
    3,253
    They have worked well for me. I have only shot cast in them.
    NRA Benefactor Member NRA Golden Eagle

  4. #4
    Boolit Master
    Join Date
    Dec 2016
    Posts
    1,091
    I think these were made by Captech, which has been closed for awhile,so if you need to add to your supply I would get them while they are available. Mine have only been loaded a few times with cast and no issues. Some Remington brass has become available also, so I have stocked up a bit on them too.

  5. #5
    Moderator Emeritus


    georgerkahn's Avatar
    Join Date
    Sep 2013
    Location
    South of the (Canada) border
    Posts
    3,053
    I bought some a while back, for my one and only Krag (long gone), and my recollection is it loaded well -- BUT, I do not recall reloading said brass any more than maybe twice. The Krag I had had been sporterized, and when I found myself able to send it down the road, hesitated not. NO PROBLEMS, again, with the brass. At the time, I loaded/shot factory jacketed bullets in it -- don't recall which, but they seemed unGodly long...My loading was about 1/2-way between min and max, in Ken Water's Pet Loads.
    geo

  6. #6
    Boolit Master
    Join Date
    Feb 2011
    Location
    SE Kentucky
    Posts
    1,309
    Bought some for reforming to 30/40AI. After forming have been reloaded six times with no issues (neck sized).

  7. #7
    Moderator
    Texas by God's Avatar
    Join Date
    Mar 2016
    Location
    Texas
    Posts
    14,335
    Thank you everyone. I've placed my order. Is the rear face of the rim beveled as on the originals?

  8. #8
    Boolit Master
    Join Date
    Feb 2011
    Location
    SE Kentucky
    Posts
    1,309
    Yes they are beveled.

  9. #9
    Moderator
    Texas by God's Avatar
    Join Date
    Mar 2016
    Location
    Texas
    Posts
    14,335
    I got them in. They look great but they aren't beveled. They're probably made from .303 British stock but I bet they work. The Lee dies are beautiful and Grafs saw fit to send a Lee primer pocket cleaner free! Good times.

    Sent from my SAMSUNG-SM-G930A using Tapatalk

  10. #10
    Vendor Sponsor

    Chill Wills's Avatar
    Join Date
    Oct 2011
    Location
    Was-Colorado, Wyoming now
    Posts
    3,151
    Hmmmm.... Yours say BCC on the head stamp. Mine say Graf.

    The 500 lot I got about two years ago from Grafs is a little larger than my R-P 30-40 cases. Larger just ahead of the rim and the case necks are thicker too. Not surprising, the cases weigh more than the old R-P cases and have a little less volume too. About 3 grains less.
    Chill Wills

  11. #11
    Boolit Master
    Join Date
    Feb 2011
    Location
    SE Kentucky
    Posts
    1,309
    Interesting! When I posted about the bevel I compared the Graf brass to some Win brass. After seeing the pic I went back and looked again. Depending on who made the brass and maybe when the bevels were different. Some were small, some large like the R-P pictured and some were in between, even from the same maker (Win).

  12. #12
    Boolit Grand Master


    swheeler's Avatar
    Join Date
    Mar 2005
    Location
    Montana
    Posts
    5,471
    The W-W Super brass I've got has the large bevel like the Remington brass shown here.
    Charter Member #148

  13. #13
    Boolit Grand Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    13,617
    I just necked my first 50 BCC brass from .30 to 7mm to .25 without a problem or a crease. I hope to get to the range this weekend to fireform some of them. Ordered another 100.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  14. #14
    Vendor Sponsor

    Chill Wills's Avatar
    Join Date
    Oct 2011
    Location
    Was-Colorado, Wyoming now
    Posts
    3,151
    Click image for larger version. 

Name:	resizeDSCN1765.jpg 
Views:	19 
Size:	67.6 KB 
ID:	235533
    This is some of that Graf 30-40 brass set up in the lathe to reduce the web area ahead of the rim. I use the 30-40 Krag brass as bases for the 40-60 Maynard case to be shot in a BPCR match rifle. The chamber in that rifle was spec'd using the slightly smaller R-P Krag brass and as it turned out, I could not use the Graf brass with out turning it to fit.

    The Graf brass does have a slightly smaller powder capacity. I have shot the same pieces 5-6 times working up a load. The only match, and the only target in that match I have used it, 300 meter pigs, it shot fine hitting 10 for 10 animals.
    I will know more about how good it is after a season of loading and shooting each piece about 20 times.
    Last edited by Chill Wills; 02-07-2019 at 09:08 PM.
    Chill Wills

  15. #15
    Boolit Grand Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    13,617
    I just posted my process for making the 25 Krag AI in the section for reforming brass.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check