Inline FabricationWidenersMidSouth Shooters SupplyRotoMetals2
Lee PrecisionRepackboxTitan ReloadingADvertise here

Donate Now Goal amount for this year: 6000 USD, Received: 5750 USD (96%)
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Page 2 of 2 FirstFirst 12
Results 21 to 27 of 27

Thread: cigarette roller ???

  1. #21
    Boolit Master
    Join Date
    May 2012
    Posts
    1,625
    If you can find one. Old Benson & Hedges rolling machine works well. Never had much luck with the Zig-Zag or Top rollers which is a clone to Zig Zag machines. But I've always thought if somehow I could shorten a Top machines width so to barely accommodate a cast? It may be useful for the purpose.
    To be honest. To date. I have never seen a boolit rolled tighter than those I've wrapped by hand. Although if I'm unable to roll years from now. No doubt my wife would help me out.
    "JUST A OLD DEPLORABLE THAT'S IRREDEEMABLE."

  2. #22
    Boolit Buddy Old Coot's Avatar
    Join Date
    Mar 2008
    Posts
    314
    It must be human nature to try so hard to make simple tasks more difficult.
    Lay the cut and wet paper on a board or mouse pad perpendicular to the edge facing you, with about 1/3 of it hanging over the edge closest to you.
    Place the bullet with the nose facing to the right on the paper with enough paper to the left of the bullet laying free to make your twist tail.
    Pick up the short end of the paper (that closest to you) and lay it across the bullet. It should not reach the long piece of paper laying on the pad or board.
    Place the pad of your index or middle finger on the paper covering the top of the bullet and roll the bullet and paper away from you.
    You should now have a bullet covered by a tube of paper with a hollow tube of paper sticking out below the base.
    Grasp that hollow tube of paper with the thumb and index finger of your left hand and GENTLY twist the paper and bullet in opposite directions while pushing them together.
    You now have a wet patched bullet with a twist tail. Stand the patched bullet upright in an ammo box and let dry over night.
    Clip the tail when dry with a pair of toenail clippers or diagonal cutters, lube and load.
    Brodie

  3. #23
    Boolit Master


    rfd's Avatar
    Join Date
    Feb 2013
    Location
    NJ via TX
    Posts
    3,178
    ... or just wrap with dry paper and slip into pre-loaded cases.

  4. #24
    Boolit Buddy
    Join Date
    May 2012
    Posts
    359
    Click image for larger version. 

Name:	20190208_012551.jpg 
Views:	35 
Size:	37.8 KB 
ID:	235548

    Here is a pic of the patching board i made . I added the lines to help get them all the same.
    We go through life trying to make the best decisions we can based on the best infomation we can find, that turns out to be wrong.

  5. #25
    Boolit Master
    Join Date
    May 2010
    Location
    central texas
    Posts
    629
    Thanks everyone. I had been patching 45 slugs with dry paper but found wet paper to patch well on the 30 cal so long as I do not stretch enough to get an overlap.

  6. #26
    Boolit Master scattershot's Avatar
    Join Date
    Sep 2011
    Location
    Denver, CO
    Posts
    964
    I have the same question about cigarette papers. I am loading .430 boolits in a .444 Marlin. Two wraps of cigarette paper give me .434, which is just about perfect. Is the cigarette paper too flimsy to make a good patch?

    Thanks.
    "Experience is a series of non-fatal mistakes"


    Disarming is a mistake free people only get to make once...

  7. #27
    Boolit Master
    Tom W.'s Avatar
    Join Date
    Mar 2005
    Location
    Phenix City, Alabama
    Posts
    3,649
    When I was rolling smokes I got a roller from a head shop in Woodstock. That was before my handloading days.....
    Tom
    μολὼν λαβέ


    Did I ever mention that I hate to trim brass?

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check