WidenersMidSouth Shooters SupplyLee PrecisionRepackbox
Titan ReloadingInline FabricationLoad DataRotoMetals2
Reloading Everything
Results 1 to 15 of 15

Thread: Is stability for a given twist a function of bullet length or weight?

  1. #1
    Boolit Buddy
    Join Date
    Jan 2018
    Location
    Sydney, Australia
    Posts
    213

    Is stability for a given twist a function of bullet length or weight?

    I have a .357 Maximum rifle with a 22" barrel and 1:18.7" twist.

    The 180gn cast bullets i have tried in the rifle have proven to be inaccurate and many people more experienced with this caliber are of the opinion that the twist is too slow for the heavy bullets.

    The rifle shoots 1 hole clusters with 158gn Jacketed so that kind of proves their point.

    So i'm looking for a mold around the 158gn weight but i have seen a couple of molds designed for powder coating where the lack of a lube groove means a 170gn PC bullet is the same cross section as a 158gn bullet with lube grooves.

    So my question is.
    Would the stability be the same with a heavier bullet that is the same length as a lighter one?

  2. #2
    Boolit Buddy Cast_outlaw's Avatar
    Join Date
    Oct 2018
    Location
    B.C. Canada
    Posts
    419
    That’s a good question I’m going to keep my eye on this thread

  3. #3
    Boolit Grand Master


    Join Date
    Apr 2017
    Location
    Aberdeen, South Dakota
    Posts
    7,136
    A 180 grain bullet is stable from a 1:18" twist 357 magnum at less than 1200 fps. Bullets in excess of 220 grains can also be stable from a 357 magnum handgun. Your twist rate is not the problem.

    Stability is a function of bullet length, but also effected by velocity. The faster it's launched, the higher the RPM's.

  4. #4
    Boolit Master Hannibal's Avatar
    Join Date
    Sep 2013
    Location
    East of KCMO
    Posts
    2,190
    More a function of twist and velocity. Sometimes a longer barrel can increase the velocity enough to aid stability, but not always. A short bullet generally weighs less and requires less twist because it will attain higher velocity without excessive pressure.
    Think RPM. That's where the magic is.

  5. #5
    Boolit Master 5Shot's Avatar
    Join Date
    Apr 2005
    Location
    Colbert, WA
    Posts
    722
    Length and velocity. Bullets like the Barnes are longer for their weight, so they need a faster twist than a standard bullet of the same weight. Cast bullets are the shortest for a given weight, so you can shoot a heavier bullet than you can with jacketed. When you are right on the edge, pushing a long bullet faster can keep it stable until it slows down below a certain threshold.
    If you live on the razor's edge and slip, you will die in two pieces

  6. #6
    Boolit Master 5Shot's Avatar
    Join Date
    Apr 2005
    Location
    Colbert, WA
    Posts
    722
    According to the Berger Stability Calculator, with that twist, your bullet should be stable even at subsonic velocity. Even a 200 grn cast bullet is stable below 800 fps.
    If you live on the razor's edge and slip, you will die in two pieces

  7. #7
    Boolit Master
    Join Date
    Oct 2013
    Posts
    911
    on stability calculators if you leave everything the same and move weight up and down stability goes up and down with it. which is new to me I just thought length and rpm was all you needed. but also whats missing is im pretty sure center of mass matters even if its not on the calculators. or maybe that's the only reason why they ask weight is to shift center of gravity?

  8. #8
    Boolit Grand Master

    Join Date
    Mar 2013
    Location
    Northwest Ohio
    Posts
    14,462
    I have been told by a few length is what you stabilizing but in reality you cant make a longer lighter bullet so weight does play a part. AS mentioned above the solid coppers are longer for a given weigh. In my 300 win mag 180 partitions shoot exceptional the 180 barnes is barely acceptable with slightly oval holes at longer ranges. Same weights but different lengths. The 150 barnes is a stellar performer though. Velocity does play a big role in stabilizing a bullet

  9. #9
    Boolit Grand Master


    missionary5155's Avatar
    Join Date
    Feb 2007
    Location
    Last trip to Arequipa... till April.
    Posts
    7,133
    Greetings
    The calculators are not perfect. There are many factors they do not take into the formulas neither can they. With all the variations they are simple guidelines. Much like the "Greenhill" formula... it is a nice guide but is not exact in all applications.
    RPM's for your slug from your rifle will differ a bit from my combination when we approach that "instability threshold".
    When it happens it can go south fast. But boost the velocity some and maybe it will fly straight another 20 yards further.
    "Come unto Me, all you who labor and are heavy burdened, and I will give you rest." Matthew 11:28
    Male Guanaco out in dry lakebed at 10,800 feet south of Arequipa.

  10. #10
    Boolit Master
    Join Date
    Jun 2010
    Location
    WNY
    Posts
    2,504
    First, your 1:18 twist should stabilize the 180g bullet. I have two .357max guns and both have a 1:20 twist barrel (not the ideal twist I might add). They can stabilize a 180g bullet reasonably well. I can get jacketed 180g bullets to shoot five shots around 1.25-1.5" groups at 100 yards. That's stable enough for deer hunting. Being an accuracy nut, it isn't what I want it to do. Shooting 158g jacketed bullets the guns will shoot five shots into an inch or just a bit less at 100 yards. I have pages of data developed with many powders and bullets over the last several years. The last barrel I bought, an MGM barrel for my Encore, is a 1:20 twist. MGM insisted that a 1:20 would stabilize any bullet, even the heaviest ones. Their "experts" said so. I've had several custom built .357 handguns and rifles in the past, really high end guns. The master gunsmiths who built them told me that the best twist for a .357 bullet is 1:16 or a 1:14, with the 1:16 being the most common. I know that from experience they are correct. However, I deferred to MGM's suggestion and it's been an exercise in futility to get great groups from their 1:20 twist with any bullet or load when the bullet is over 158g. Cast bullets are the hardest to get to shoot really well, not just because of the bullets being heavier, but you can't drive them fast enough to stabilize well with a 1:20 twist. Also, as you probably know, every feature of a cast bullet can effect accuracy.....dia of base and bands, lubes, nose profile, etc, etc, etc. Summary: the 180g bullets I did get to perform "well enough" were Hornady 180g XTP's using Rel7 powder. Again, they're very adequate for deer hunting. Don't listen to the seller when buying a Max barrel, they'll sell you what ever they have on the shelf they want to get rid of. Aside from all of this, the MGM barrel does shoot the 158g very well and I shot three deer with it this year, two complete passthroughs and one recovered bullet with perfect expansion and weight retention. Good luck with your gun.

  11. #11
    Boolit Master
    Join Date
    May 2012
    Location
    Outside Rolla, Missouri
    Posts
    2,170
    You can dance around with all sorts of things or just use the Greenhill formula and be both right and done. I haven't used it in thousands of calculations but for 20 or so rifles it's been on the money.

    http://kwk.us/twist.html
    "In general, the art of government is to take as much money as possible from one class of citizens and give it to another class of citizens" Voltaire'

    The common virtue of capitalism is the sharing of equal opportunity. The common vice of socialism is the equal sharing of misery

    NRA Benefactor 2008

  12. #12
    Boolit Master
    GARD72977's Avatar
    Join Date
    Aug 2008
    Location
    TUPELO MS
    Posts
    1,726
    It is length that you are stabilizing. An example of lighter long bullets would be tracers.

  13. #13
    Boolit Master


    Join Date
    Mar 2005
    Location
    Perryville, Ky,USA
    Posts
    4,513
    And, I'll throw another variable in the equation. Now, this is my own humble opinion. Bullet design also affects stability. Cases in point are the 148 grain wadcutter in the .38 Special. Loses velocity quickly past 50 yards. This is primarily due to velocity loss. The old touted 200 grain "Police Load" in the .38 Special has been accurate for me out to 100 yards for plinking. One of the attributes is that once it hits something, it goes crazy tumbling through whatever it hits. That's why it was so popular as a man stopper in police use. Another factor is "Where is the center of gravity". I've shot bullets with so-so accuracy, hollow pointed them and accuracy is enhanced. The .30 Ness no ricochet design is a real mystery. Big old long 170 grain lead cylinder with a huge open cavity. I tested these with George XXX for several months one summer. They work as I was firing into a flat looking for ricochets into a berm at 100 yards. None detected after 40 rounds. I fired 5 for group at 100 yards. Went into less than an inch at 100 yards. I like to have had a heart attack at that result. Fired the last 5 rounds and again a sub 1" group at 100 yards. Probably the best I've ever fired with a .30/06.

    This matter has been discussed at length for years and will be for many more years. We just don't know at this time.

    I do know that rotation plays a big part. You can use velocity to overcome instability as long as your pressure envelope is safe. The design and center of gravity make a difference as well.

    All you can do is keep trying and find what works for you./beagle
    diplomacy is being able to say, "nice doggie" until you find a big rock.....

  14. #14
    Boolit Grand Master


    Larry Gibson's Avatar
    Join Date
    Jul 2005
    Location
    Lake Havasu City, Arizona
    Posts
    21,306
    CamoWhamo

    "The 180gn cast bullets i have tried in the rifle have proven to be inaccurate

    As beagle mentions there are many things that affect "accuracy" besides stability. Both jacketed and cast bullets can be stable in flight yet wildly inaccurate. If the bullet holes are round in the 100 yard target they are "stable".

    What is the 180 gr cast bullet in question?

    What is the length of the bullet?

    To specifically answer the question; "Would the stability be the same with a heavier bullet that is the same length as a lighter one It would be very close as there is a constant/factor in stability formulas (including Greenhill's) that accounts for the mass of a bullet. Most lead based cast bullets have a close enough mass to fall within that constant/factor. However, if we seriously change the mass of a given size bullet, say one cast of #2 alloy and one cast of aluminum, then the stability will be much different.
    Larry Gibson

    “Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.”
    ― Nikola Tesla

  15. #15
    Boolit Grand Master popper's Avatar
    Join Date
    Jun 2011
    Posts
    10,572
    Stability has 2 factors. Rotational momentum and CF/CG relationship. Momentum is based on mass (which is related to length) for a given material. So what does momentum do? Keeps the boolit going in a strait line. Air velocity forces act on center of gravity and center of force to cause the straight line path to change to a nutating path (helical spiral). That spiral cone can be decreasing or increasing diameter.It is caused by gyro precession. So 'stability' is controlled by twist (momentum) and boolit design. Then there is the transonic region where shock waves act on the CG/CF.
    Whatever!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check