Inline FabricationRotoMetals2Graf & SonsWideners
StainLess Steel MediaRepackbox

Results 1 to 12 of 12

Thread: Drying .45 cases

  1. #1
    Boolit Buddy
    Mr Peabody's Avatar
    Join Date
    Dec 2005
    Posts
    462

    Drying .45 cases

    Yesterday was rainy so I ran a few pounds of .45 acp brass through my sonic cleaner. I don't use the kitchen oven to dry it. I place it on a towel by the heater and it takes a few hours to dry. While I was in the garage digging out Christmas goodies I saw an old food dehydrator my wife bought years ago.
    Grabbing it up I took it to my shop and loaded it with my wet brass. In an hour all was good. Warm and very dry brass. Worth a go if you have a dehydrator.

  2. #2
    Boolit Buddy
    Join Date
    Dec 2017
    Location
    Farmerville,Louisiana
    Posts
    376
    Sounds like your repurposing that dehydrator for drying brass, no more jerky with that one.

  3. #3
    Boolit Master flyingmonkey35's Avatar
    Join Date
    Apr 2014
    Location
    Utah
    Posts
    1,086
    You can find old food dehydrator at thrift stores all the time for a few bucks.

    Cheap and effective

    Sent from my SM-G960U using Tapatalk

  4. #4
    Boolit Master Reverend Al's Avatar
    Join Date
    Feb 2013
    Location
    Victoria, B.C., Canada
    Posts
    1,420
    I've been using a 7 tray food dehydrator to dry my wet brass ever since I bought my ss pin tumbler. Works great ...
    I may have passed my "Best Before" date, but I haven't reached my "Expiry" date!

  5. #5
    Boolit Master
    Join Date
    May 2013
    Location
    Indianapolis, indiana
    Posts
    1,217
    lyman even makes a dryer that looks much like a dehydrator.

  6. #6
    Boolit Buddy
    Join Date
    Dec 2018
    Posts
    289
    But please remember that a lot of the home appliances that get found at good will very often are dropped off at good will because of odd issues. In other words, once you have to jiggle the on/off switch 3 times each direction to turn it on, off to good will it goes.

  7. #7
    Boolit Master

    Join Date
    Oct 2009
    Location
    England,Ar
    Posts
    4,477
    I have a dedicated baking sheet that I use. In the Summer I lay it on the tool box on my trailer and let the sun work. In the winter they go into the oven for 45 minutes at 200. I used an old food dehydrator some but it took longer if I counted the time loading the trays.

  8. #8
    Boolit Master

    MrWolf's Avatar
    Join Date
    Apr 2013
    Location
    NE West Virginia
    Posts
    1,883
    I also use a food dehydrator. Didn't work well on food but great for drying brass.

  9. #9
    Boolit Master
    georgerkahn's Avatar
    Join Date
    Sep 2013
    Location
    South of the (Canada) border
    Posts
    868
    Great re-use of an appliance! Sadly, I believe the dehydrator we had was donated to a Salvation Army store. I had no need until three or four years ago when -- thanks to this site -- I both learned about, bought the hi-speed Thumler's Tumbler, and got hooked on SSW wet tumbling. Initially, I placed my brass on window screens in the sun -- but -- with so few sunny days -- and, my not really wanting to leave them out, open, unattended -- I saw a Franfort appliance specifically made for drying brass. While it has a thermostat to control the heat fans blow, I wanted, too, just air sans heat. Hence, I did a wee bit of surgery on the unit, inserting a toggle switch in series with the thermostat, so I may just use ambient air. On a countdown timer, I love being able to set it for (my usual) 4 hours, and "forget it" -- say, the next day have all my brass dry, and ready for the loading room.
    geo

  10. #10
    Boolit Master Walks's Avatar
    Join Date
    Jun 2016
    Location
    SoCal
    Posts
    855
    Great use for an unused appliance. Around here I cannot find anything in the thrift stores, usefull to me, anyway.

    I'm using the same different method for drying cases, I've used for years. Ever since I started using the Birchwood Casey concentrate. I have a 1"x 6" x 36" board covered with a grid pattern of 3" finishing nails.
    I size/decap the brass first. Then wash it.
    Just blow out the empty primer pockets of the cases as I drop them over each nail.
    With so much Sunshine here, they're dry in an hour or two. Drying Rack takes 208 cases.
    I have a Sonic Cleaner now, but still dry the same way.
    Happiness is a Warm GUN & more ammo to shoot in it.

    My Experience and My Opinion, are just that, Mine.

  11. #11
    Boolit Master

    nicholst55's Avatar
    Join Date
    Jan 2007
    Location
    Daegu, Korea
    Posts
    2,864
    Quote Originally Posted by Walks View Post
    Great use for an unused appliance. Around here I cannot find anything in the thrift stores, usefull to me, anyway.

    I'm using the same different method for drying cases, I've used for years. Ever since I started using the Birchwood Casey concentrate. I have a 1"x 6" x 36" board covered with a grid pattern of 3" finishing nails.
    I size/decap the brass first. Then wash it.
    Just blow out the empty primer pockets of the cases as I drop them over each nail.
    With so much Sunshine here, they're dry in an hour or two. Drying Rack takes 208 cases.
    I have a Sonic Cleaner now, but still dry the same way.
    Sounds very similar to how I dried brass at Yuma Proving Ground, AZ - just put it on the back porch for a while in the sun.
    Boycott YouTube

  12. #12
    Boolit Master bdicki's Avatar
    Join Date
    Mar 2010
    Location
    Central Florida
    Posts
    925
    Hair dryer.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check