Inline FabricationRotoMetals2StainLess Steel MediaWideners
RepackboxMidSouth Shooters SupplyGraf & Sons

Results 1 to 6 of 6

Thread: Cheap Case Induction Annealer Experiment

  1. #1
    Boolit Buddy
    Join Date
    Aug 2005
    Location
    Central Texas
    Posts
    387

    Cheap Case Induction Annealer Experiment

    Hi guys,

    I thought you might be interested in an experiment I ran to determine if I could make a cheap case neck induction annealer. The experiment was not a success but you may learn something from the article which is posted at the following link.

    http://www.texas-mac.com/Cheap_Case_...xperiment.html

    Wayne
    NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
    http://www.texas-mac.com

  2. #2
    Boolit Master

    Bent Ramrod's Avatar
    Join Date
    Apr 2005
    Location
    Southern Arizona
    Posts
    3,204
    That’s an informative article.

    If you used the original 2” coil and put a piece of 1-3/4” steel round stock with a 1/2” hole in the center inside, would the steel cylinder generate and maintain sufficient heat so you could stick the case necks in the hole to anneal? Could you turn the current down to control the heat to a given temperature? Or would this setup draw more current and burn the unit up like the smaller coil?

    I was always wondering if it would be possible to turn and thread a copper cylinder of the proper size, use it to replace the tip on a heavy-duty electric soldering iron, and put the case neck over the cylinder for sufficient time to see the color change. But what I don’t know about electricity and electronics would fill a volume.

  3. #3
    Boolit Buddy
    Join Date
    Aug 2005
    Location
    Central Texas
    Posts
    387
    Quote Originally Posted by Bent Ramrod View Post
    That’s an informative article.

    If you used the original 2” coil and put a piece of 1-3/4” steel round stock with a 1/2” hole in the center inside, would the steel cylinder generate and maintain sufficient heat so you could stick the case necks in the hole to anneal? Could you turn the current down to control the heat to a given temperature? Or would this setup draw more current and burn the unit up like the smaller coil?

    I was always wondering if it would be possible to turn and thread a copper cylinder of the proper size, use it to replace the tip on a heavy-duty electric soldering iron, and put the case neck over the cylinder for sufficient time to see the color change. But what I don’t know about electricity and electronics would fill a volume.
    Brent,

    Thanks. I appreciate your suggestion which is similar to one another guy on this forum that sent me via a PM suggesting I try the 2" coil with a smaller diameter iron or steel rod setting on an insulated base. The rod diameter would be slightly smaller than the inside of the case neck. I plan to try both suggestions & will report the results here.

    BTW, with the power supply I'm using there's no way to control the output voltage or current. Also, if either one of the suggestion work I'll most likely have to switch power on & off as the cases are inserted since the metal rod or tube would most likely heat up to the point of melting during an annealing session if the power is not cycled on & off.

    Wayne
    Last edited by texasmac; 12-10-2018 at 12:24 PM.
    NRA Life (Benefactor & President's Council) Member, TSRA Life Member, NSSF member, Author/Publisher of the Browning BPCR book.
    http://www.texas-mac.com

  4. #4
    Boolit Master
    Join Date
    May 2014
    Posts
    692
    Banggoods.com has inexpensive power supplies and ZVS drivers. Just over $100.00 for both that I am getting. I also purchased graphite crucibles so I can melt scrap brass.

    I'll be using litz wire to make other coils. Tubing and multi stranded litz wire reduce surface eddy effect. Also adding insulation between the objective and the coil.
    Last edited by jdfoxinc; 12-10-2018 at 01:56 PM.
    QUIS CUSTODIET IPSOS CUSTODES?

  5. #5
    Boolit Grand Master
    Join Date
    Aug 2005
    Location
    South Jersey
    Posts
    5,088
    Wayne - interesting read but WAY over my head to assemble & connect all the items ... so, turn the lights down low - propane torch - twist the case with my thumb & index finger and when the case color from the mouth down is bluish/green (625 - 650F) ... drop it on a cotton cloth to air cool
    Regards
    John

  6. #6
    Boolit Grand Master popper's Avatar
    Join Date
    Jun 2011
    Posts
    7,900
    The cheapest and most efficient electric annealed would be a ceramic rod of less than mouth ID heated by normal cal rod.
    Whatever!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check