StainLess Steel MediaInline FabricationWidenersRotoMetals2
RepackboxMidSouth Shooters SupplyGraf & Sons

Results 1 to 5 of 5

Thread: CZ 455 varmint

  1. #1
    Boolit Master
    idahoron's Avatar
    Join Date
    Jul 2007
    Posts
    1,344

    CZ 455 varmint

    I was doing some shooting a while back. I discovered that if I load the shells one at a time into the chamber instead of using the mag, my rifle shoots a lot smaller groups. Has anyone else tried this? At 50 yards I went from 1" 5 shot groups to 1/2" or less 5 shot groups.

  2. #2
    Boolit Grand Master tazman's Avatar
    Join Date
    Jan 2014
    Location
    west central Illinois
    Posts
    5,036
    It helped a tiny bit in my 452 trainer. Not a dramatic difference such as you are talking about. But then, I was already getting groups well under 1 inch at 50 yards anyway.

  3. #3
    Boolit Buddy arcticap's Avatar
    Join Date
    Oct 2008
    Location
    Central Connecticut
    Posts
    167

    Not only the CZ 455 Varmint

    Thumbing bullets into the chamber is a practice that I've routinely done with .22lr bolt actions when sighting in and during light rifle and other informal .22LR matches.
    When loading directly from the magazine and then ejecting without firing the bullet, it became evident that bullets can became deformed when chambered feeding with the bolt.
    It's something to be aware of even for junior rifle competitors who shoot single shot rifles or for those who use single shot adapters.
    The adapters don't always line up the cartridge to feed perfectly into the chamber.
    Nicks on the bullets may or may not have much of an effect on accuracy at all.
    Each rifle is different but sometimes it's better to be safe than sorry and doesn't hurt to thumb the bullets in.
    It becomes 2nd nature and some guns with thicker diameter bull barrels have an even higher angle of bullet entry into the chamber when fed from the magazine.

  4. #4
    Boolit Buddy Randy Bohannon's Avatar
    Join Date
    Oct 2016
    Location
    Buffalo WY
    Posts
    218
    I read a few months ago from one the U.K. rimfire forums, these guys shoot everything they can get their hands on. It was an obvious observation in ther conversations they all universally agreed that Weight sorting your ammo was the single best thing you do to improve accuracy in any rimfire.

    I just went through sorting 250 rounds of Eley/Remington Club 40gr LRN .22 LR, it shoots just ok in the 3 CZ's 22 LR I have without weight sorting, when I started to weigh them in a RCBS digital scale it became an obvious to sort groups, greater than 52 grs. less than 52 grs. I was shocked the weight variances the lighest was 48.8grs. and the heaviest was 54.3grs. I will be shooting these in the next day or so with a scoped CZ453 American. I don't expect much of an improvement, we will see.

    I just bought 3 box's of Norma 40gr LRN"Tac 22" they were 5$ at Sportsman Warehouse I had shot one box a few day's ago sighting in a new CZ 452 Training rifle with a Anschutz diopter peep sight and the factory hooded front sight it shot 1" but nearly a foot high, need new front sight. It's a pain to put a good diopter sight on a CZ. I don't why no company has'nt jumped on reasonal priced one for the CZ rifles. But anyway this stuff is within .5 gr. from the heaviest to the lightest. I think these should shoot very well with the 453.

  5. #5
    Boolit Master Tripplebeards's Avatar
    Join Date
    Apr 2017
    Location
    Southwest, Wisconsin
    Posts
    1,296
    I bought a used 452 utralux super exclusive last year. Cleaned it and tested about a dozen different types of ammo. No expense match stuff yet. I have a leupold 2x7 vx1 with a parallex set at 150 yards from what I've read so it explains why it looks kinda fuzzy at 50 yards when I load tested it. The best I did were half inch 5 shot groups with cheap Winchester 555 ammo. That was letting it feed through the mag. I tried three different aguila loads and they were 6" to 9" groups! Also tried the CCi quiets and they never exited the barrel. The gun sounded like it never went off so I knew what happened. The load made it to the last inch of the barrel and I pushed it out with a cleaning rod. Tried it one more time with the same results. CZ and CCi both told me the inside bore diameter of CZ rimfire rifles are a little tighter than the average 22lr creating more friction along with the longer barrel was a double negative. CCi prints on the quiets box not to shoot in barrels over X amount of length but mine never had it on it. CCi ended up with my ammo and sent me some standard velocity ammo on trade.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check