Would a .41 inch punch be wide enough to compress BP in a .45-70 case?
Would a .41 inch punch be wide enough to compress BP in a .45-70 case?
With a heavy wad like the 060 thick harder materials it should be okay, with thinner lighter wads it may allow the edges to fold up around it. .410 is roughly 050 small or .025 on a side.7/16 or .440 would be better. The head on a 3/8 allen head cap screw might be very close to what you want a little work with it clamped in a drill and file could take it to just what you want. Another to check would be a 1/4" flat heads head dia.
I just saw a Lyman M die in .41 cal for ten bucks and wondered if I could use it to compress BP using a press. I guess I’ll pass on it. Thanks for your input.
Just thinking. If I went with a cap screw or a flat head, I could chuck it in my drill press and adjust it for the same depth each time. That should work shouldn’t it?
You might be able to lock a washer between 2 nuts for a stop on the case mouth if the nut will fit inside the case mouth. Depending on the compression it may be hard on a drill press rack and pinion/spindle. Off the top of my head a 1/4" nut is 7/16" across the flats so it might just go. If the nuts are big enough 2 nuts jammed in location would do it. compress to the nut just touches and your there.
$20 gets you one, a good one at that, that you can install in a die body you have now.
Here is a link....
https://www.buffaloarms.com/reloadin...-body-van45rcp
Chill Wills
This is one of those deals if you gonna do it - do it right! I dont reckon a drill press would be accurate enough and the compression stem needs to be fairly neat in the case and straight every stroke - If you really need to save some bucks can buy bolts with the thread to fit your RCBS die body (I believe they 9/16th NF) but then you need a lathe to turn the shank. I would make one myself - I have the lathe and if I scratch around in my workshop for a bit the bolt will be there someplace - but to save twenty bucks ??? ................................not really
indian joe is correct - do it right. just get the proper BACO plug and stick in a lyman "M" die body and be done with it.
I have now cut a good fitting tool of my own but when I started out, I just bought a 7/8" 14tpi bolt to thread into my press and used a .38 Special case with a black line on it to compress the powder.
Worked fine and cost a grand total of $2.50
Will Buffalo Arm’s compression die fit into any other than a Lyman M die. I’m using a tablet and all of Buffalo Arm’s pages get cut off at the right so I can’t read everything.
I called them about the pages being cut and apparently nothing can be done about it.
Track of the Wolf sells compression plugs specifically built for Lee dies.
Long range rules, the rest drool.
Buy a bolt with the threads of the internal die threads you will use to compress the powder. I made one each for my 45 and 40 brass. A couple of minutes in the lathe and you will have the bolt head round and fitting in the brass case. No lathe? A grinder or belt sander will do the job too.
NRA Life
NMLRA Life
F&AM
If you have a LEE universal expander, check Track of the Wolf. If you don't have the LEE die, get one. They are very handy with all the plugs you can get from NOE and Track of the Wolf. Don't scrimp on good tools.
You can often buy a used Lyman M die at a gun show for $5.00. I buy a 3 foot length of the appropriate thread size and turn it down in a lathe to make various size compression dies.
And heck of lot cheaper than M-Dies!Track of the Wolf sells compression plugs specifically built for Lee dies.
https://www.trackofthewolf.com/Categ...IE-45-COMPRESS
One Lee expander die and as many caliber plugs for 3 bucks that you have rifles with different calibers ... I got a whole box of these plugs for my different caliber rifles
Regards
John
A 1.5" piece cut off the shank of an old 29/64" drill bit, cut and ground flat and square, fits perfectly into a 45-70 case. Unscrew the the expander end from the expander stem and use that as a compression die.
After dropping the powder I push the wad into the case, push the wad down to the powder with the drill shank, leave in place, insert into shell holder and set compression depth as you would with any other die.
Dave
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |