RepackboxRotoMetals2MidSouth Shooters SupplyLoad Data
Titan ReloadingWidenersReloading EverythingLee Precision
Inline Fabrication
Results 1 to 7 of 7

Thread: Powder coat back or bottom of cast bullet?

  1. #1
    Boolit Mold
    Join Date
    Nov 2018
    Posts
    13

    Powder coat back or bottom of cast bullet?

    First time poster, new to casting and powder coating, forgive dumb question. If I spray pc it will require more work to pc bottom AND top, is there a need to pc bottom?

  2. #2
    Boolit Master
    farmerjim's Avatar
    Join Date
    Nov 2012
    Location
    St. Francisville, Louisiana
    Posts
    1,925
    No need to PC bottom.
    There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand

  3. #3
    Banned
    Join Date
    Jul 2016
    Posts
    2,911
    Dowright- welcome to CB. If you decided to start casting to save money, forget it. You won't, you'll just shoot more.

    There are many threads on powdercoating and the search box at the top right of the page is your best friend. IF yu can't find what yor looking for searching ask.
    I'd be surprised if someone here didn't have the answer. There are NO dumb questions. everyone starts somewhere and it's best to start the right way.

    It is not necessary to coat the bottom of a boolit (boolit = lead bullet) PC (powdercoat) takes the place of lube or the jacket and is only needed where the boolit contacts the rifling.
    You would be hard pressed to spray without covering the "top" nose of the boolit

    Casting boolits (lead bullets) properly is a science, once you know the basics, not a hard science.
    There is a lot of good information on CB. The Google search (top right of every forum page) is a gateway to all the knowledge on this forum. IF you can’t find your answer there ask the question (Please be as detailed as possible, pictures help http://castboolits.gunloads.com/show...g-screen-shots I would be very surprised if there wasn’t someone on this forum that could answer ANY (firearm related) question you might have)
    http://www.lasc.us/Fryxell_Book_Contents.htm
    1. Boolits need to be cast .0005 to .003 (normally .002) over the slugged diameter of your barrel for accuracy and to avoid leading. If the fit is wrong nothing else will work right.
    a. slugging a barrel (it is safer to use a brass rod or a steel rod with a couple of coats of tape to avoid damaging your barrel http://7.62x54r.net/MosinID/MosinSlug.htm
    b. chamber casting https://www.brownells.com/guntech/ce....htm?lid=10614
    or pound casting http://castboolits.gunloads.com/show...rifle-chamber)
    2. the right alloy needs to be used for the velocity and purpose of the boolit (don’t fall into the trap of going with too hard an alloy

    Economical way to easily test lead hardness
    http://castboolits.gunloads.com/show...rdness-testing

    Some alloys harden over time
    http://www.lasc.us/Fryxell_Book_Chap...Metallurgy.htm
    different alloy’s different end hardnesses


    Lead alloy calculator
    http://castboolits.gunloads.com/atta...4&d=1341560870
    3. velocity the bullet needs to be pushed hard/fast enough to get the proper spin, have the proper velocity to accurately reach the target but not so hard as to be dangerous or strip the lead off in the grooves instead of spinning the boolit..
    The boolit needs to be the right weight for the riffling/twist rate of your barrel
    Powders range from fast to slow, you need to choose the right powder for your barrel length & application.
    Loading manuals list the best powders for certain calibers and boolit weights.
    NEVER use any posted noncommercial load data without first checking commercial load data to see if falls in the safe parameter for your firearm!! There are several firearms out there that can handle much higher pressures than others!!
    Link to free online load data
    http://castboolits.gunloads.com/show...online-sources

  4. #4
    Boolit Grand Master popper's Avatar
    Join Date
    Jun 2011
    Posts
    10,572
    Depends. I tried not coating PB for high pressure rifle, results were bad - edge of the base isn't coated and gets gas cut. My ES sprayer is gathering dust as I changed to ASBBDT. Gets the entire boolit. I apply GC first and then tumble/cook. Resize if needed. I did test uncoated nose vs complete coat - nope, not accurate.
    Decided to PC this morning, really dry air as my sinuses note. 35F, powder was in the tub all summer and we've had LOTS of rain, tub is just snap on type. Cold boolits, about 30 sec. of swirl & shake - does fine. Heaping teaspoon of powder per 10# boolits.
    Tried the dump method, not for me - too messy. Pick out with hemo and base down on NSAF or parchment paper. Still haven't swiped the thin flexible copper cooking sheet from her to try. Did try the silicon trivit - nope. PC didn't stick to it but it got sticky and smelly. Too many boolits stuck together. I cook on a hat plate just till I get flow so they are easy to handle. Cook to cure in toaster oven later - makes easier to tranport the heavy tray without domino effect.
    Whatever!

  5. #5
    Boolit Grand Master fredj338's Avatar
    Join Date
    Feb 2009
    Location
    kalif.
    Posts
    7,202
    Quote Originally Posted by Dowright View Post
    First time poster, new to casting and powder coating, forgive dumb question. If I spray pc it will require more work to pc bottom AND top, is there a need to pc bottom?
    Need no, desirable yes. Uncoated bullet bottoms are like FMJ with open base. I shake & bake, so the bottom of my bullets are coated, much like a plated bullet, completely enclosed.
    FWIW, my shooting needs are not dictated by cost, more time & location. So yes, casting & coating my own saves me a lot. I shoot about 10K rds a year in idpa competition & practice. Buying bullets would cost me about $1000.
    EVERY GOOD SHOOTER NEEDS TO BE A HANDLOADER.
    NRA Cert. Inst. Met. Reloading & Basic Pistol

  6. #6
    Boolit Master
    Dragonheart's Avatar
    Join Date
    Jan 2012
    Location
    Katy, Texas
    Posts
    2,705
    If you are just starting out I would recommend getting a powder that works from Smoke and try the shake & bake method instead of spraying. The benefit is a completely coated bullet cooked standing up will give you a flat base; there will be no problem with seal or gas cutting. I typically only spray hollow points & gas check bullets. Spraying costs more and is more time consuming.

  7. #7
    In Remembrance - Super Moderator & Official Cast Boolits Sketch Artist

    RP's Avatar
    Join Date
    Mar 2008
    Location
    Nahunta NC
    Posts
    3,410
    If you PC the bottoms with bright colors you can see them going down range so much better
    Reloading to save money I am sure the saving is going to start soon

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check