Inline FabricationGraf & SonsWidenersMidSouth Shooters Supply
Lee PrecisionRepackboxTitan ReloadingRotoMetals2
StainLess Steel Media
Results 1 to 14 of 14

Thread: 30-06 blanks

  1. #1
    Boolit Buddy
    Join Date
    May 2006
    Location
    Jacksonville, NC
    Posts
    238

    30-06 blanks

    Can 30-06 blanks be used to for regular full power loads?

    I came into some fired LC blanks that I'd consider turning into reloads. I remember hearing that 5.56 blanks with the star crimp couldn't be used as the brass was weaker. Now I see guys using it for 300 BLK cases. Obviously that's different.

    I'm not short of brass, but I'd prefer not to take usable brass to the recycle man.


    Sent from my iPhone using Tapatalk

  2. #2
    Boolit Master
    429421Cowboy's Avatar
    Join Date
    Apr 2011
    Location
    Montana
    Posts
    1,113
    Someone correct me because I'm likely wrong, but I seem to remember something about '06 blanks being thicker, thus having reduced capacity that obviously spikes pressure?
    Raisin' Black Angus cows, outta gas, outta money, outta tags, low on boolits, but full 'a hope on the Rocky Mountain Eastern Slope!
    Why does a man with a 7mag never panic buy? Because a man with a 7mag has no need to panic!

    "If you ain't shootin', you should be reloadin' if you ain't reloadin' you should be movin', if you ain't movin', somebody's gonna come by and cut your head off and put it on a stick!" Words to fight by, from Clint Smith

  3. #3
    Boolit Master
    429421Cowboy's Avatar
    Join Date
    Apr 2011
    Location
    Montana
    Posts
    1,113
    http://castboolits.gunloads.com/show...06-Blank-cases
    This might be of help as well.

    Cheers,
    Cowboy
    Raisin' Black Angus cows, outta gas, outta money, outta tags, low on boolits, but full 'a hope on the Rocky Mountain Eastern Slope!
    Why does a man with a 7mag never panic buy? Because a man with a 7mag has no need to panic!

    "If you ain't shootin', you should be reloadin' if you ain't reloadin' you should be movin', if you ain't movin', somebody's gonna come by and cut your head off and put it on a stick!" Words to fight by, from Clint Smith

  4. #4
    Boolit Buddy
    Join Date
    May 2006
    Location
    Jacksonville, NC
    Posts
    238
    The thread referenced above is a great one; I had considered using only cast in these cases due to these kind of pressure concerns.

    My pet 30-06 cast load is 20.0 gr 2400 under a lee 170 gr bullet. I think it is their copy of the Lyman 31141. I would likely start at about 18 and work to 20. That load is just magic in my Ruger M77.

  5. #5
    Boolit Master
    Join Date
    May 2007
    Posts
    3,355
    as the sage observation, made by Ben, it's a hit & miss on the quality of blank brass. that said, I annealed some blank brass, trimmed it up, inspected it and loaded standard loads. YMMV

  6. #6
    Boolit Master
    Join Date
    Aug 2007
    Location
    So. Indiana
    Posts
    1,071
    I did this awhile back and still have a few of the cases as I can tell by the ring on the neck. They worked fine. If memory serves, I also inside neck reamed the necks. I believe most of them are gone now as I was shooting them in a match were it was hard to recover the empties. I have plenty of -06 brass now.

  7. #7
    PAPERPATCH MASTER


    Join Date
    Oct 2008
    Location
    Michigan Thumb Area
    Posts
    5,737
    Many years back I was given an MG belt of .30-06 blanks that were Canadien made. About the same time I heard not to use the brass due to various irregularaties from normal brass. I still have about 200 unfired .30-06 Canadien blank rounds in a special container marked with what they are.Robert

  8. #8
    Boolit Master



    wgr's Avatar
    Join Date
    Jul 2008
    Location
    indiana
    Posts
    982
    I have used them to form 8mm out of

  9. #9
    Boolit Master

    Uncle Grinch's Avatar
    Join Date
    Jul 2005
    Location
    Middle Georgia
    Posts
    1,253
    As common as 30-06 brass is, I wouldn’t even consider using blank brass for anything other than its intended use. Outside of the question of strength, the work involved to reform this brass is not worth the effort if there is any question on its reliability.

    Understand that this is my opinion....
    Shoot Safe,
    Mike

    Retired Telephone Man
    NRA Endowment Member
    Marion Road Gun Club
    ( www.marionroad.com )

  10. #10
    Boolit Buddy
    Join Date
    May 2006
    Location
    Jacksonville, NC
    Posts
    238
    There's no forming needed, just a resize and trim to length. And remove a military crimp.

    Thanks for all the replies, set up my prep station last night and should be able to finish prepping them this week.


    Sent from my iPhone using Tapatalk

  11. #11
    Boolit Bub Postell's Avatar
    Join Date
    Sep 2013
    Location
    Indiana
    Posts
    51
    I have never had any problems using them with full loads.

  12. #12
    Boolit Master
    Join Date
    Mar 2005
    Posts
    3,626
    I have used the 30-06 blanks with the ringed necks and paper wad discs with out any problems.
    EDG

  13. #13
    Boolit Man
    Join Date
    Feb 2007
    Posts
    87

    Maybe once

    Quote Originally Posted by 0802 View Post
    Can 30-06 blanks be used to for regular full power loads?

    I came into some fired LC blanks that I'd consider turning into reloads. I remember hearing that 5.56 blanks with the star crimp couldn't be used as the brass was weaker. Now I see guys using it for 300 BLK cases. Obviously that's different.

    I'm not short of brass, but I'd prefer not to take usable brass to the recycle man.


    Sent from my iPhone using Tapatalk
    I say no because of the blanks crimp I can see the end of the neck separating at the weakened juncture , Causing the gun to be useless .

  14. #14
    Boolit Master

    merlin101's Avatar
    Join Date
    Mar 2010
    Location
    Rochester NY heading to Gaults Gulch
    Posts
    1,164
    I have no experience with 06 blanks but have had plenty of headaches with 5.56 blanks converted to 300BO. Everything from primer pockets being deformed and made shallower when swaging to neck thickness not being consistent. I would be very hesitant to use blanks for brass, it's obvious that it is a lower quality.
    It's not the years in your life that count. It's the life in your years (Abe Lincoln)

    "A free people ought not only to be armed and disciplined, but they should have sufficient arms and ammunition to maintain a status of independence from any who might attempt to abuse them, which would include their own government. George Washington

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check