RotoMetals2Graf & SonsMidSouth Shooters SupplyInline Fabrication
StainLess Steel MediaWidenersRepackbox

Page 2 of 2 FirstFirst 12
Results 21 to 26 of 26

Thread: 30-40 Krag CB load experts ... Help?

  1. #21
    Boolit Grand Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    6,250
    Nick,

    Measuring the throat diameter is easy. The easiest way to measure a .303 or Krag chamber is to take a factory .38 Special soft-swaged lead, round-nosed bullet, drop it into the chamber, and then use a section of squared off, chamfered and polished 3/8" brass or aluminum rod to pound it into the chamber neck until the drive rod comes to a stop against the shoulder of the chamber. Then just tap the slug back out from the muzzle and measure it with a micrometer. This lets you capture the chamber neck diameter, case mouth transition, and throat diameter, which are all you need to know to order your mold from Accurate or NOE.

    Click image for larger version. 

Name:	No4LongBranch303ThroatSlug.jpg 
Views:	13 
Size:	36.7 KB 
ID:	228963
    Last edited by Outpost75; 10-16-2018 at 03:43 PM.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  2. #22
    Quote Originally Posted by Outpost75 View Post
    Nick,

    Measuring the throat diameter is easy. The easiest way to measure a .303 or Krag chamber is to take a factory .38 Special soft-swaged lead, round-nosed bullet, drop it into the chamber, and then use a section of squared off, chamfered and polished 3/8" brass or aluminum rod to pound it into the chamber neck until the drive rod comes to a stop against the shoulder of the chamber. Then just tap the slug back out from the muzzle and measure it with a micrometer. This lets you capture the chamber neck diameter, case mouth transition, and throat diameter, which are all you need to know to order your mold from Accurate or NOE.

    Click image for larger version. 

Name:	No4LongBranch303ThroatSlug.jpg 
Views:	13 
Size:	36.7 KB 
ID:	228963
    That is a much less messy way of getting a chamber throat measurement,
    All this time I have been slopping Cerrosafe (spelling?.. ) all over the darn place.
    Going to try that ,, thanks.
    Keep breathing , it's good for ya...

  3. #23
    Boolit Buddy ELFEGO BACA's Avatar
    Join Date
    Jan 2007
    Location
    Idaho Territory USA
    Posts
    207
    Click image for larger version. 

Name:	3FDD699F-9821-48CC-A0D3-05FFDFE4EB99.jpg 
Views:	14 
Size:	51.5 KB 
ID:	230876
    First try with a recently purchased Krag was with a 200 grain cast bullet from a Saeco 301 mold sized .309”.
    Traditional alox/beeswax homemade lube.
    Too high on 100 yd target but right on using bottom aperture of ladder at 200 yd plates!
    Lucky!
    I used Hornady cases and filled each with 19.4 grains of R7, a 200 grain cast bullet, and A CCI primer.
    Average velocity for five shoots was 1496 ft/sec!
    Last edited by ELFEGO BACA; 11-27-2018 at 10:41 PM. Reason: Add info
    Relax! The turkeys ran off.

  4. #24
    Boolit Buddy
    Join Date
    Feb 2007
    Posts
    152
    I have used these in a 30-40 handi rifle. 200 grain, lubed sized to .311 and gas checked. Use with 2400 load data from Lyman 49.

    Careful about trying to run this above 2000 fps. I get pressure signs and poor accuracy above 1800 fps.

    http://westernbullet.com/311299br200gr.html
    Last edited by clearwater; 11-23-2018 at 11:40 PM.

  5. #25
    Boolit Buddy ELFEGO BACA's Avatar
    Join Date
    Jan 2007
    Location
    Idaho Territory USA
    Posts
    207

    Cool 240 yard targets

    Click image for larger version. 

Name:	677A759A-E061-4F3D-A3F5-B967F392557B.jpeg 
Views:	17 
Size:	132.2 KB 
ID:	231548
    Click image for larger version. 

Name:	D34C47B4-0F43-4ADE-9E2A-44887ADA7B1F.jpeg 
Views:	21 
Size:	173.1 KB 
ID:	231549
    Click image for larger version. 

Name:	E0D0B125-AC14-4C3D-8BB6-746E1B6AAD43.jpeg 
Views:	19 
Size:	181.8 KB 
ID:	231550
    Today I managed to make a few hits on my 240 yard plates using
    200 grain cast bullets at a muzzle velocity of 1496ft/sec.
    Relax! The turkeys ran off.

  6. #26
    Boolit Bub Nick Adams's Avatar
    Join Date
    Feb 2010
    Location
    Midwest
    Posts
    35
    Quote Originally Posted by ELFEGO BACA View Post
    Click image for larger version. 

Name:	677A759A-E061-4F3D-A3F5-B967F392557B.jpeg 
Views:	17 
Size:	132.2 KB 
ID:	231548
    Click image for larger version. 

Name:	D34C47B4-0F43-4ADE-9E2A-44887ADA7B1F.jpeg 
Views:	21 
Size:	173.1 KB 
ID:	231549
    Click image for larger version. 

Name:	E0D0B125-AC14-4C3D-8BB6-746E1B6AAD43.jpeg 
Views:	19 
Size:	181.8 KB 
ID:	231550
    Today I managed to make a few hits on my 240 yard plates using
    200 grain cast bullets at a muzzle velocity of 1496ft/sec.
    Very nice! Thanks for sharing those pics!
    Underneath our starry, starry flag,
    We civilized 'em with a Krag.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check