Inline FabricationReloading EverythingRotoMetals2Wideners
RepackboxTitan ReloadingMidSouth Shooters SupplyLee Precision
Load Data
Results 1 to 20 of 20

Thread: Anybody ever loaded 2 patched round balls in a rifle at the same time?

  1. #1
    Boolit Master roverboy's Avatar
    Join Date
    Feb 2010
    Location
    Moss,Tn.
    Posts
    1,110

    Anybody ever loaded 2 patched round balls in a rifle at the same time?

    I've heard of this but, never tried it. Seems like it would be a good deer load in the woods. Definitely different.
    Mrs. Hogwallop up and R-U-N-N-O-F-T.

  2. #2
    Boolit Master scattershot's Avatar
    Join Date
    Sep 2011
    Location
    Denver, CO
    Posts
    1,532
    I did it once, just to see what would happen. Can’t remember now just what did happen, except that it increased recoil by a bit. If you try this, he ****ED SURE you seat the second ball firmly on the first, or it will act as a bore obstruction and possibly ring your bore.
    "Experience is a series of non-fatal mistakes"


    Disarming is a mistake free people only get to make once...

  3. #3
    Boolit Master
    Join Date
    Mar 2010
    Posts
    562
    Caution... check your state regs..I lived in Indiana then and I think ML rules required the use of a single ball... think OH and PA are same. I tried it many years ago on paper and both shot well @ 50yds only about 1-2" horizontal spread(IIRC), but be careful... I think I loaded the first ball on top of the powder without a patch and than patched the second ball and seated firmly... you do not want any gaps... the recoil should be about the same as when you shoot a maxi-ball...

    TheMoose
    Perhaps my learning skills have diminished in my senior years.. 50 years ago I could read something once and then "have it"... Now I read it about three times, do it a couple of times and then... "have it" only about half the time.

  4. #4
    Boolit Master
    Join Date
    May 2010
    Location
    Chula Vista, CA
    Posts
    1,145
    During a recent match I did a double load, powder, patch and ball. The top powder load did not go off and even if it had I doubt it would have damaged the modern barrel. There were two ball marks on my steel target though which really surprised me!
    John

  5. #5
    Boolit Master arcticap's Avatar
    Join Date
    Oct 2008
    Location
    Central Connecticut
    Posts
    585
    I tried it with 2 patched round balls rammed down firmly on the powder charge.
    The balls hit very close together at 25 yards.
    It's not a load that I would hunt with though
    Buck & ball loads were used during the Revolution and Civil War but with large caliber muskets.
    ========
    Buck and ball

    Buck and ball was a common load for muzzle-loading muskets, and was frequently used in the American Revolutionary War and into the early days of the American Civil War.
    The load usually consisted of a .50 to .75 caliber round lead musket ball (.69 caliber for the "Brown Bess" musket) that was combined with three to six buckshot pellets.

    https://en.wikipedia.org/wiki/Buck_and_ball

  6. #6
    Boolit Grand Master

    Beagle333's Avatar
    Join Date
    Mar 2012
    Location
    Back in the woods a piece, just outside Auburn, AL.
    Posts
    5,499


    This guy makes fun videos and he recently posted one on this.
    KE4GWE - - - - - - Colt 1860, it just feels right.

  7. #7
    Boolit Buddy
    Join Date
    May 2013
    Location
    OH
    Posts
    272
    I did it out of a cva .50 with a stubbed off barrel about 1-2" spread @ 25 yds right on point of aim. neat load to mess around with

  8. #8
    In Remembrance Reverend Al's Avatar
    Join Date
    Feb 2013
    Location
    Victoria, B.C., Canada
    Posts
    1,899
    When our local Black Powder club used to hold "stake shoots" it was common practice to "double-ball" since the name of the game was the first team to cut their stake off completely was the winner. One year a friend of mine got a little bit carried away and put in a heavy powder charge and then TRIPLE-BALLED his .45 calibre percussion rifle. When it went off the pressure blew the entire drum and nipple out of the barrel! (We never did find the drum either so it must have gone a fair distance ...) As a general rule MODERATE powder charges with a double-ball load have been quite successful without incident, but I sure wouldn't recommend pushing the limits of safety ...
    I may have passed my "Best Before" date, but I haven't reached my "Expiry" date!

  9. #9
    Banned


    Join Date
    Feb 2013
    Location
    NJ via TX
    Posts
    3,876
    normally not an issue unless the charge is at the high end, and buck 'n' ball is similar.

  10. #10
    Super Moderator


    ShooterAZ's Avatar
    Join Date
    Jan 2012
    Location
    Flagstaff, AZ
    Posts
    12,065
    It's been done before, that's how Jed Clampett struck oil if I recall.

  11. #11
    Boolit Master


    dondiego's Avatar
    Join Date
    Jan 2013
    Location
    Milan, MI
    Posts
    2,814
    I was in a hurry and loaded a patched round ball and a ram rod once and fired it at a rabbit. It had some good recoil! Missed the rabbit and never did find that ram rod.

  12. #12
    Boolit Grand Master bedbugbilly's Avatar
    Join Date
    Sep 2013
    Location
    MI (summer) - AZ (winter)
    Posts
    5,098
    The only time I've done it is when "proofing" a barrel with a double charge with the barrel strapped to a rubber tire - ignited by a piece of fuse.

  13. #13
    Boolit Master

    TCLouis's Avatar
    Join Date
    Mar 2005
    Location
    Middle TN
    Posts
    4,404
    Wonder why he uses such undersized balls?
    0.480 in a 50 Cal?
    Amendments
    The Second there to protect the First!

  14. #14
    Boolit Master arcticap's Avatar
    Join Date
    Oct 2008
    Location
    Central Connecticut
    Posts
    585
    I think it's because he likes to use his thumb instead of a short starter to start the ball, and then just rams it.

  15. #15
    Boolit Master


    Rick N Bama's Avatar
    Join Date
    Apr 2005
    Location
    In the Heart of N Alabama smack dab along Tornado Alley.
    Posts
    1,132
    On Facebook Mark said it was because he can load more without having to clean the barrel. The .480 RB Mold is available from TOW
    Democracy is two wolves and a
    lamb voting on what to have for lunch. Liberty is a well-armed lamb contesting
    the vote. - Benjamin Franklin

  16. #16
    Boolit Master roverboy's Avatar
    Join Date
    Feb 2010
    Location
    Moss,Tn.
    Posts
    1,110
    I've been meaning to try this in my .58 cal. with about 60-65 gr. 2f Goex.
    Mrs. Hogwallop up and R-U-N-N-O-F-T.

  17. #17
    Boolit Master

    Join Date
    Feb 2007
    Location
    Lewiston, Idaho
    Posts
    2,732
    I've one a few stake shoots over the years. First shot is alway loaded normal then things change fast. Up to five un-patched balls in a 62 with 60 grains of powder will eat a lot of wood in a hurry. This is only used in timed events, not for hunting. The range is usually under 40 yards and accuracy is not that important when you have that much lead going down range. This was done with a rifle that I built and know it would hold up, I don't recommend this on every rifle.

  18. #18
    Banned
    Join Date
    May 2016
    Location
    Derby, UK.
    Posts
    283
    With buck and ball' loads, which is loaded nearer the powder?

  19. #19
    Banned


    Join Date
    Feb 2013
    Location
    NJ via TX
    Posts
    3,876
    buck then ball.

  20. #20
    In Remembrance Reverend Al's Avatar
    Join Date
    Feb 2013
    Location
    Victoria, B.C., Canada
    Posts
    1,899
    Quote Originally Posted by dondiego View Post
    I was in a hurry and loaded a patched round ball and a ram rod once and fired it at a rabbit. It had some good recoil! Missed the rabbit and never did find that ram rod.
    Reminds me of a Rendezvous one year when a friend was shooting a Parker Hale Muskatoon repro carbines and he got flustered and left his aluminum ramrod in the barrel and then fired it. We had a line of targets cliped on to an upper and lower piece of heavy wire using wooden clothes pegs. His ramrod hit the wire target holders and took down the entire line of targets. I'll never forget it ... and I'm sure that he never did either!
    I may have passed my "Best Before" date, but I haven't reached my "Expiry" date!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check