RotoMetals2MidSouth Shooters SupplyLee PrecisionWideners
Titan ReloadingGraf & SonsInline FabricationStainLess Steel Media

Results 1 to 9 of 9

Thread: litho sheets

  1. #1
    Boolit Master
    Join Date
    Feb 2017
    Location
    NWO sunset country
    Posts
    239

    litho sheets

    have acquired several hundred sheets of print plates, these aluminum sheets mic out at .012 plus or minus, they seem fairly soft & bend very easily and can be easily straightened. Question is? has anybody tried these for gas checks I have recently purchased new PM 44 &45 dies and really don't want to destroy them if I can help it (I'm known for that sort of thing around here) should I be annealing these if so how much heat and how long? If it will work I have probably got 25 lifetimes supply. suggestion and info would be a huge help.

  2. #2
    Boolit Master
    Rcmaveric's Avatar
    Join Date
    Jul 2017
    Location
    Jacksonville, FL
    Posts
    963
    I use aluminium sheets that mic around .008 for my 6.5 gas checks. Then for .270 I use .012 sheeting. If it is soft then there is no need to anneal. It wont do anything.

    Sent from my SM-G950U using Tapatalk
    "Speak softly and carry a big stick; you will go far."
    ~Theodore Roosevelt~

  3. #3
    Boolit Master
    Join Date
    May 2014
    Posts
    630
    S couple of members also use them. Go ahead.
    QUIS CUSTODIET IPSOS CUSTODES?

  4. #4
    Boolit Master Grmps's Avatar
    Join Date
    Jul 2016
    Posts
    2,632
    Nice find. I'm jealous, they make great gas checks.

    For the calibers, I make gas checks for, 22 - 32 cal
    Last edited by Grmps; 09-05-2018 at 11:16 AM.

  5. #5
    Moderator



    JonB_in_Glencoe's Avatar
    Join Date
    Mar 2010
    Location
    Land of 10,000 Lakes
    Posts
    10,615
    PM dies are made for specific material thickness.

    Are your PM dies for plain base boolits? If so, I suspect .012 is too thick.
    If they are for conventional GC boolits with gas check shank, .012 may be too thin (for 44 or 45) to get crimped tightly onto the shank when put in the size die.

    As to hardness, you won't wreck your dies just trying to cut .012 litho...if it's too hard, you'll get tearing instead of shearing...as well as having some forming problems. I use .006 litho for 22 cal checks, it isn't too hard, doesn't need annealing.
    Good Luck

  6. #6
    Quote Originally Posted by brass410 View Post
    have acquired several hundred sheets of print plates, these aluminum sheets mic out at .012 plus or minus, they seem fairly soft & bend very easily and can be easily straightened. Question is? has anybody tried these for gas checks I have recently purchased new PM 44 &45 dies and really don't want to destroy them if I can help it (I'm known for that sort of thing around here) should I be annealing these if so how much heat and how long? If it will work I have probably got 25 lifetimes supply. suggestion and info would be a huge help.
    Where did you find it? I am personally on lookout for any aluminum sheet source and soft aluminum is great.

    Sent from my SM-G950U1 using Tapatalk

  7. #7
    Boolit Master
    Join Date
    Feb 2017
    Location
    NWO sunset country
    Posts
    239
    the local print shop does some custom work so they still use one of the older lithograph machines I enquired about aluminum sheets for another project and they said come out back and they set 2 skids about 50 inch high on my truck and said a donation to the shop coffee fund would be great! I can go back any time a get more if I have need for them (I gave several timmys gift cards and mugs)

  8. #8
    Boolit Master
    Join Date
    Mar 2005
    Location
    southern Illinois
    Posts
    2,131
    I have used the exact thing for 30 cal checks and they work very well. Since there was no way to crimp them on, they were used only for full power loads. They may be better than factory checks....


    P.S. In a full power load, the tapered check shank on the bullet and the aluminium check smash in and fill the grooves full.... Amazing what 40,000 psi can do...

  9. #9
    Boolit Man
    Join Date
    Aug 2010
    Location
    Ontario, Canada
    Posts
    94
    Quote Originally Posted by Rcmaveric View Post
    I use aluminium sheets that mic around .008 for my 6.5 gas checks.
    I also make 6.5 gas checks, using .008" litho plates and homemade dies. I get great results, no annealing necessary.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check