CLOSED- MP-Molds - Shotshell BUCKSHOT mold

[DukeInFlorida]

Since these cavities will be made with a small ball mill (no custom cherry required), we will go with the 000 Buck size. I need your details to add you.

if 000 were to happen I'd be in

[DukeInFlorida]

Those of you who dreamed of #000 Buckshot, please get me your details, so I can add you.
The rest of the requests have been added, thanks!

I'm in for:

Nueces (1) 8 cav aluminum shot shell mold for #1, mhkilgore at mac dot com, 78620 DHL shipping

Nueces (1) 8 cav aluminum shot shell mold for #0, mhkilgore at mac dot com, 78620 DHL shipping

Interested also in #000

I'm interested have to see if the #00 can be fit into the budget. Dog had a vet bill for dislocated hip and I just made a contribution to my dentist sending their kid to Harvard if you get what I mean.

Ok got that ironed out, and decided the #0 was the ticket so...

RogerDat (1) 8 cavity aluminum shot mold for #0 without handle, drccac at zoomon with a dot and net. Yes that is dot net not dot com, 48836 DHL shipping

I'm assuming (and hoping) the Lee 6 cavity mold handles will fit. Is that correct or is there some other domestic handle I might already have that will fit these molds?
Also if it turns out not enough interest in #0 and there is enough interest in the #00 then I could switch. I already have a .310 RB mold so it would have to be the 0 or 00 for me.

Sorry Duke, E-mail: dale 1 at idworld dot net

readr1 (1) 8cav #1 shot readr1 at yahoo dot com 76020 DHL

jdfoxinc
jdfoxinc at aol dot com
80211

One 0 mold
One #1 mold

could be interested if it was 000 buck.

RogerDat (1) 8 cavity aluminum shot mold for #0 without handle, drccac at zoomon with a dot and net. Yes that is dot net not dot com, 48836 DHL shipping

I'm assuming (and hoping) the Lee 6 cavity mold handles will fit. Is that correct or is there some other domestic handle I might already have that will fit these molds?
Also if it turns out not enough interest in #0 and there is enough interest in the #00 then I could switch. I already have a .310 RB mold which is same as #1 so it would have to be the 0 or 00 for me.

475AR- (1) 8 cav aluminum shot shell mold for #1 shot, sddeem AT hotmail dot com, 34209 Zip Code DHL Shipping

[jmort]

#000 will not fit in a wad but has great terminal effect.
A Teflon sleeve and a gas check and you are golden

[rancher1913]

put me down for the ooo as well, all details are in first post now.

[AggieEE]

OK Duke 78108.

[zymguy]

3) zymguy - (1) 8 cav aluminum shot shell mold, #000 shot, << Need rest of details, please

zymguy at gmail DOT com

[RogerDat]

Man I hope we get the numbers to make this happen! Buckshot and slug are the loads for shotguns that save enough to really be worth doing for the casual shotgun user. And yes this is a bump.

[DukeInFlorida]

All current new orders and details added.
I will ask HATCH to move this to the ACTIVE area. We now have 18 orders.

[Minerat]

Duke add me please

Minerat - (1) 8 cavity aluminum shot shell mold, #0 shot size, SteveOB at outdrs dot net, 80003 Zip Code, 1 handles.

[edp2k]

toy $ funds are currently depleted, I must decline a 000 mold at this time, sorry.

[ramhunter]

ramhunter here

I will take : 1 8 cav #1 buck mold with handles

yukonmarco at gmail dot com..

thank you

[shawnsmc]

Shawnsmc, I'll take one #1 shot. Shawn smc at hot mail dot com. Zip code 95037

[6pt-sika]

Don’t mean to pour salt in the wound so to speak but all the 00 I’ve ever had my hands on measured closer to .34” rather than .33” . And as to 000 it closer to .36” not .336” which I assume is a typing error . I’d be intrested in 0000 .38” and 00000 .40” . Already cast those two with a two cavity Lee molds and it’s kinda SLOW .

[DukeInFlorida]

Added, thanks

Duke add me please

Minerat - (1) 8 cavity aluminum shot shell mold, #0 shot size, SteveOB at outdrs dot net, 80003 Zip Code, 1 handles.

Removed, sorry to see you go. Let me know if things change.

toy $ funds are currently depleted, I must decline a 000 mold at this time, sorry.

Added, thanks. Need your full details to make the job easier when invoicing and shipping happens. See the list, above in the first post, for the details that I need.

ramhunter here

I will take : 1 8 cav #1 buck mold with handles

yukonmarco at gmail dot com..

thank you

Thank you, added

Shawnsmc, I'll take one #1 shot. Shawn smc at hot mail dot com. Zip code 95037

I'm going to stick to the sizing for the #00 from the chart. After lead has been bounced around in the factory, it's going to be all dented, dimpled, etc. And, therefore somewhat difficult to measure as it came from a mold. By staying with the official USA designation, we will be sticking with the traditional size that it SHOULD BE.

With regard to the #000 shot size, that was a quirk of my attempts to do a fast copy and paste, and has been corrected to the .36" per the chart. Thanks for pointing that out.

Anything above #000 buckshot goes well beyond the scope of this group buy, and would become somewhat of a custom one-up kind of mold. The 38 special and 40 cal sizes are special use. I would suggest that you seek out one of the one-up type custom mold makers to make those for you.

Don’t mean to pour salt in the wound so to speak but all the 00 I’ve ever had my hands on measured closer to .34” rather than .33” . And as to 000 it closer to .36” not .336” which I assume is a typing error . I’d be intrested in 0000 .38” and 00000 .40” . Already cast those two with a two cavity Lee molds and it’s kinda SLOW .

[6pt-sika]

Anything above #000 buckshot goes well beyond the scope of this group buy, and would become somewhat of a custom one-up kind of mold. The 38 special and 40 cal sizes are special use. I would suggest that you seek out one of the one-up type custom mold makers to make those for you.

Far easier and more economical to go on Track of the Wolf for Lee 6 cavity .380" and .395" round balls then paying for something one off .

[Ed K]

Ed K - (1) 8 cav aluminum shot shell mold, #1 shot size, mvesk at yahoo dot com, 03046 Zip Code

[DukeInFlorida]

Added, thanks

Ed K - (1) 8 cav aluminum shot shell mold, #1 shot size, mvesk at yahoo dot com, 03046 Zip Code

[DukeInFlorida]

Sorry it took me a bit to get your order(s) all straight. Should be fine hnow.

put me down for the ooo as well, all details are in first post now.

[karlB]

I like to order two molds, one for reload 4 pellets per layer and one for 3 pellets, both with felt wad or wads without the "paddels".
My calculation for the maximum diameter of one pellet is as followed:
3 per layer: r=[2*sqrt(3)-3]*shell inner diameter = 0.4641 x 0.74 ~ 0.343 I decide 00 Buckshot

4 per layer: r=[sqrt(2)-1]*shell inner diameter = 0.4142 x 0.74 ~ 0.3065
Based on this the minimum shell inner diameter with 0.31 pallets is 0.7484, I guess this pellets will fit too tight. But I am sure that the 0.31 pellets will not fit in any wad with paddels.

Thats why I would prefer a mold in 0.300

I hope my english is good enough for understanding.

[DukeInFlorida]

The #1 (.031") buckshot mold is the smallest we are making for this buy.
So, I will add you for the #00 buckshot mold, but you'll have to figure something else out for your .300" needs.
I need your disguised email address, and postal code (for tracking details when this ships) to complete your listing in the orders.

I like to order two molds, one for reload 4 pellets per layer and one for 3 pellets, both with felt wad or wads without the "paddels".
My calculation for the maximum diameter of one pellet is as followed:
3 per layer: r=[2*sqrt(3)-3]*shell inner diameter = 0.4641 x 0.74 ~ 0.343 I decide 00 Buckshot

4 per layer: r=[sqrt(2)-1]*shell inner diameter = 0.4142 x 0.74 ~ 0.3065
Based on this the minimum shell inner diameter with 0.31 pallets is 0.7484, I guess this pellets will fit too tight. But I am sure that the 0.31 pellets will not fit in any wad with paddels.

Thats why I would prefer a mold in 0.300

I hope my english is good enough for understanding.