WidenersMidSouth Shooters SupplyLee PrecisionRepackbox
Inline FabricationStainLess Steel MediaRotoMetals2Graf & Sons
Titan Reloading
Page 2 of 2 FirstFirst 12
Results 21 to 26 of 26

Thread: Full power load required to size brass?

  1. #21
    Banned
    Join Date
    Feb 2013
    Location
    Boulder CO
    Posts
    760
    In any event. No, full power loads are not needed to fire form. I like 14 grs of Alliant 410 topped up with cornmeal and sealed with a wax cap. Any light load of fast powder topped with cornmeal or COW will work well - the filler expands the brass effectively.

  2. #22
    Boolit Buddy
    Join Date
    May 2005
    Posts
    100
    Lyman Item # 2660299 303 RN GC 200 gr 314299

  3. #23
    Boolit Grand Master


    Larry Gibson's Avatar
    Join Date
    Jul 2005
    Location
    Lake Havasu City, Arizona
    Posts
    16,619
    Okay, that's a good bullet. Yes 16 gr of 2400 may fire form the cases, especially if a Dacron filler is used. I suggest 18 gr with the bullet seated out so it is firmly seated against the leade when the cartridge is chambered. You may also want to slightly lube the cases so they don't stick to the chamber walls. You want the case head thrust against the bolt face so the case shoulder is blown forward to fire form.
    Larry Gibson

    Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.
    ― Nikola Tesla

  4. #24
    Boolit Master
    Join Date
    Jul 2013
    Location
    Florida
    Posts
    582
    Get a 32 caliber mold for your model 99, I'm using a 100 grain .312 Lee mold and loading them as dropped over 5 or 6 grains of Bullseye, I use the .7 cc Lee powder dipper. It works great to fire form trimmed 30-06, 270 and even 8x57 brass to use as 7.7x58 brass. You only need a light load to move the brass and shooting plinkers is a ball out to about 50 yds.

  5. #25
    Boolit Grand Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    10,435
    Yup, item # and mold # are very different things. We typically use mold number here - thus the confusion. Thanks for clearing it up.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  6. #26
    Boolit Master

    Rcmaveric's Avatar
    Join Date
    Jul 2017
    Location
    Jacksonville, FL
    Posts
    1,060
    To make Grendel brass from 7.62X39 I just use my cast bullets and about 13g of 2400. Makes a nice plinking round for the kiddies to pop off for me.
    "Speak softly and carry a big stick; you will go far."
    ~Theodore Roosevelt~

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check