Graf & SonsStainLess Steel MediaTitan ReloadingMidSouth Shooters Supply
RotoMetals2Lee PrecisionInline Fabrication

Donate Now Goal amount for this year: 6000 USD, Received: 4840 USD (81%)
We have reached our goal! Thanks to all who donated! I will be updating the donation bar in the next few days!
Our Annual server fund drive is going on now! This donation drive helps fund Cast Boolits for an entire year, and helps support our 2nd amendment rights! You can donate by Paypal by clicking the DONATE button. Or by Cash / Check / MO to the address below:

Willy Snyder
PO Box 2732
Pocatello, ID 83206
****Due to overwhelming e-mails, I will be very slow in updating this list. Please bear with me!****


Results 1 to 9 of 9

Thread: CH4D Champion Press

  1. #1
    Boolit Master Rick459's Avatar
    Join Date
    Jan 2006
    Posts
    404

    CH4D Champion Press

    any one here own one? just picked one up on ebay one of the reasons are that they only have enough parts to build 11 champion presses at CH4D then they will be discontinued. also the wait to get one ordered from CH4D is 6 months. so those who have them how do you like them? i bought this press to do some light swageing.
    Rick

  2. #2
    Boolit Master



    M-Tecs's Avatar
    Join Date
    Apr 2008
    Location
    Minnesota
    Posts
    4,813
    I have one and it is outstanding.

  3. #3
    Boolit Bub
    Join Date
    Nov 2015
    Location
    wisconsin
    Posts
    45
    I like the 2 I have.

  4. #4
    Boolit Master

    Join Date
    Sep 2012
    Location
    Las Vegas
    Posts
    288
    Have had one for 45 years, 1972 $20 used. Its a beast.

  5. #5
    Boolit Master Rick459's Avatar
    Join Date
    Jan 2006
    Posts
    404
    so my other question is how much play do you have at the bell crank. as mine when i size a 45/70 case just before the bottom of the stroke the handle moves right and then left quite a ways about 1 inch. it looks like the arms at the top pins are worn pretty good. talked to CH4D they have parts but those upper pins are in there pretty tight and i will either have to make a real long punch or take it to a machine shop. any one have any experince in removing these upper pins?

  6. #6
    Boolit Master

    Join Date
    Sep 2012
    Location
    Las Vegas
    Posts
    288
    I wouldnt worry about it, mine has a bit of wiggle at the bottom of the stroke, but the ram is tighter than grannies knickers. a little oil now and then and it will outlast me.

  7. #7
    Boolit Master

    Ickisrulz's Avatar
    Join Date
    Apr 2010
    Location
    Shawnee, OK
    Posts
    2,208
    I have one and like it. It's too bad they are discontinuing them. But at $370 (plus shipping) for a single stage press I can't imagine they sell very many. Additionally, they no longer have swaging dies listed on their web page which the Champion press was recommended for.

  8. #8
    Boolit Master Rick459's Avatar
    Join Date
    Jan 2006
    Posts
    404
    the press is going back to the seller as when i spoke to CH4D they told me that was too much play in the press. i paid $332.00 for the press because i did not want to wait the 6 months to get it from CH4D ordered a new today.

  9. #9
    Boolit Master Pavogrande's Avatar
    Join Date
    Oct 2007
    Location
    Dacula Ga formerly san josie calif
    Posts
    568
    I have both a 333 and a 444 ---
    Bought the 333 a couple years ago complete for 45acp in calif for $100 and the 444 a few months ago here in georgia complete for 9mm, 38spl and 45acp for $175 -- Borh units in as new condition.
    Unfortunately between moving and house repairs I have not really used them --
    I need to make expander plugs for 30 carbine and 32 mag and some more powder bushings -
    I intend use them to replace most of the c press's when I can get back to reloading --
    So much handier having the press mounted on top of the bench -

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check