MidSouth Shooters SupplyTitan ReloadingRotoMetals2Inline Fabrication
Graf & SonsADvertise hereStainLess Steel MediaLee Precision

Results 1 to 13 of 13

Thread: 32 S&W Long Squirrel Loads ??

  1. #1
    Boolit Master

    Johnch's Avatar
    Join Date
    Jun 2005
    Location
    NW Ohio
    Posts
    2,921

    32 S&W Long Squirrel Loads ??

    Today I got to help Dad get a Chopper that extends out on a arm from a local Farm Auction
    OK I got to open up covers and see if there was leaks and grease where it wasn't wanted

    Dad was the only bidder , so that was easy

    But I just had to look at the few guns and hunting supplyes

    I saw a custom ( I think ) barrel on a H&R Handy Rifle
    The Rifle and barrel looked new , expect for the scope
    A 22" barrel with no sights , just a Weaver type Scope base & rings and a cheap Tasco Scope
    Stamped 32 S&W , nothing else

    When it came up to be bid on , there was ammo , brass , dies , bullets and powder added

    There was only 1 other person bidding also bidding on it
    I had to pay a WHOLE $45 for everything in that lot LOL

    Not sure why I bought it
    But I figure I can load ammo to hunt Squirrel a lot cheaper than 22 Lr
    IMO if the barrel is decent , accurate enough for head shots should be easy

    LOL So that means I will need to cast a few bullets to try

    But I will admit , I have never cast for or loaded 32 S&W Long
    Not even had a chance to check what bore size it is , with a custom barrel it might be .308 to .314 .... but I am betting on .308 or .310

    I will see what molds I have
    But good chances I sold all but the 1 - 130 gr mold I use for the 32 H&R mag

    2 Questions
    Good weight for a low power and accurate load in the 22" barrel
    And with what ever bullet weight a starting load

    I will most likely make a mold or 2, so a range of weights is fine

    Thanks
    John
    Yea, thou I walk through the valley of the shadow of death, I will fear no evil; for thou art with me; Thy rod and thy staff, they comfort me.
    And I carry a SIG

  2. #2
    Boolit Master Thumbcocker's Avatar
    Join Date
    Oct 2007
    Location
    East Central Illinois
    Posts
    2,242
    Sounds like a question for Outpost 75.
    You'll go far providin' you ain't burnt alive or scalped."

    Will Geer as Bear Claw in "Jeramiah Johnson"

  3. #3
    Boolit Master Texas by God's Avatar
    Join Date
    Mar 2016
    Location
    Texas
    Posts
    4,824
    Sounds like a great deal you got. Now we need pics.

    Sent from my SAMSUNG-SM-G930A using Tapatalk

  4. #4
    Boolit Master GhostHawk's Avatar
    Join Date
    Mar 2014
    Location
    Fargo ND
    Posts
    4,275
    Outpost will get here, he is the king of the .32's from what I have seen.

    I have a Rolling Block takedown chambered in .32sw long. I have not got it totally tweaked yet.
    Still working on finding what it wants.

    My favorite boolit is the Lee .314 90 gr truncated cone.
    This shoots in my H&R 732 2.5" revolver exactly to point of aim at 20 feet. As in 6 shots in an inch, offhand.

    The other mold I have is the Lee .311 90 gr round nose.

    I have also run 00 buckshot through my Lee .314 sizing die, and loaded those. They shoot pretty good as well, and cast a lot faster than the others.

    I am sticking to 2 grains of Red Dot under mine as those H&R's are fairly old and I have no desire to blow one of them up. Plus that makes for a very relaxed enjoyable shooting experience. No significant recoil or muzzle blast. Just a little pop not much more than a .22lr. Easy on old hands.

    I am looking for a Heritage Rough Rider with 6.5" barrel in .32H&R mag.
    I think I found out why they were discontinued. They are chambered, tested for .32H&R mag, but the cylinder would load and fire .327 fed mags. Which was significantly more pressure than they were designed for.

  5. #5
    Boolit Master
    Join Date
    Nov 2012
    Location
    Central Virginia
    Posts
    4,381
    Outpost75 is likely your best source of info.


    Years ago I loaded for 32 S&W Long but it was for revolvers. The gun, dies and brass were sold many years ago to fund something else that I just had to have. I was a lot younger in those days and regret that move, but live & learn.

    My common load used a full wadcutter and WW-231. I don't recall the details but the bullet was right around 100 grains and it shot well. In fact, I used the same bullet in 32 H&R Magnum with a bit more powder.

  6. #6
    Boolit Master Tripplebeards's Avatar
    Join Date
    Apr 2017
    Location
    Southern Wisconsin
    Posts
    946
    There can't be any recoil when firing that thing. For $45 I would have bought three.

  7. #7
    Boolit Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    5,812
    You are going to LOVE that rifle.

    In the .32 S&W Long you only need one mold, I recommend Accurate 31-105T
    Click image for larger version. 

Name:	31-105T-D.jpg 
Views:	11 
Size:	24.2 KB 
ID:	223671

    If your rifle is chambered for the .32 S&W (the short case)
    good bullet choices are 31-087B or 31-087T
    Click image for larger version. 

Name:	31-087B-D.jpg 
Views:	4 
Size:	20.5 KB 
ID:	223673Click image for larger version. 

Name:	31-087T-D.jpg 
Views:	4 
Size:	19.2 KB 
ID:	223674

    If you have a measure which will meter tiny powder charges, 1 grain of Bullseye is quiet like an air rifle and will exit the barrel reliably.

    A good, start load which is low noise is 1.5-1.7 grains of Bullseye, approximates .32 S&W (the short case) factory load with 31-087B bullet. RCBS Little Dandy Rotor #00

    Factory loads in .32 S&W LONG are approximated with 2 grains of Bullseye
    RCBS Little Dandy Rotor #0

    Max. in .32 S&W Long for pre-war solid-frame revolvers S&W 1903 Hand Ejector, I-frames, small frame Colt Police Positive is 2.5 grains of Bullseye. Will be subsonic in rifle. RCBS Little Dandy Rotor #1

    Heavier rifle .32 S&W LONG load which is OK in S&W Model 30 and 31, is 3 grains of Bullseye, treat as "+P"

    Another rifle load which works well is 6.3 grains of Alliant #2400, about 1250 fps. from a rifle,
    OK in S&W Model 30 and 31, but treat as "+P".
    Last edited by Outpost75; 07-15-2018 at 10:37 AM.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  8. #8
    Boolit Master gpidaho's Avatar
    Join Date
    May 2014
    Location
    Beautiful Idaho
    Posts
    1,289
    John: Let me know if you'd like to triple your money. I'd pay the shipping. Gp

  9. #9
    Boolit Master
    Join Date
    Feb 2010
    Location
    Iowa
    Posts
    1,842
    I had a H&R Handi rifle 1871 to have a barrel made for it to shoot 327mags, You will like that gun. Outpost is a good help on this.
    Life Member of NRA,NTA,DAV ,ITA. Also member of FTA,CBA

  10. #10
    Boolit Master
    Join Date
    Feb 2014
    Location
    North of Dallas 1100 miles or so
    Posts
    340
    Wow what a deal, any booolit from 70-100gr. at 800-1000fps would do the job. Todd/3leg

  11. #11
    Boolit Master

    Johnch's Avatar
    Join Date
    Jun 2005
    Location
    NW Ohio
    Posts
    2,921
    Thanks for the info
    I will have to wait to order the mold as $$ is tight
    I am in the process of changing to permanently disabled Ohio Workmans Comp
    No Workmans Comp Checks for up to a year , but a big check after all the paperwork and lawyer & Experts do their job

    John
    Yea, thou I walk through the valley of the shadow of death, I will fear no evil; for thou art with me; Thy rod and thy staff, they comfort me.
    And I carry a SIG

  12. #12
    Boolit Master Texas by God's Avatar
    Join Date
    Mar 2016
    Location
    Texas
    Posts
    4,824
    Lee TL314-90swc and 2 grs of Bullseye worked great in my .32 magnums, it would work in your rifle, too.

  13. #13
    Boolit Master


    richhodg66's Avatar
    Join Date
    Nov 2009
    Location
    Kansas
    Posts
    4,146
    I would love to have such a rifle. I have a ruined Savage 219 .30-30 barrel I will eventually turn into a Rook rifle like that, but it'll sure cost more than $45.

    Several years ago I bought an Iver Johnson top break in the short .32. Trying to figure out how to throw the tiny charges to load for it, I figured I'd give my old Lyman 55 a try and it turned out that it will throw accurate charges of Bullseye at 1.1 grain all day long.

    I'm jealous of that rifle. I've hunted squirrels with a little H&R in .30-30 and very reduced loads and it's a lot of fun.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check