MiHec 327 Single Seven 2 or 4 Cavity Brass Cramer Plain Base or Gas Check mold in Hollow Point.
This is a new boolit design. This will be suitable for the 32 H&R or 327 Fed. Magnum handguns or rifles. It will cast at about 0.314" dependent on your alloy. The weight is as shown on the drawing dependent on your alloy of choice. Meplat to crimp = 0.297".
We will need fifteen to commit to this. We will run this until we get the number we need or more, then it is up to MiHec to decide when to make it........ it can be a long time.... be warned and no whining.
Pins included are: For the Hollow Point Mold are 1) Large HP pin, 2) Cup HP pin, 3) Blank pin for a flat nose or in the case you don't want HP pins sticking out the mold.
Prices are what MiHec says they'll be. I'll have to check that out.
Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec or contacting MP Molds directly . Invoices will be sent out via e-mail from the listed e-mail addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars dependent on the time that occurs. After you pay, the mold gets shipped.
Prices are somewhat variable due to the exchange rate.... be aware of this.
Please list: your Forum name, your e-mail address in suitable disguised form (such as shooter AT gmail DOT com), the number of 2 or 4 cavity molds you want along with whether it's PB or GC.
I wanted to take a few minutes and make a few comments as to why I believe the MP Molds 327 Single Seven Mjolnir cast bullet may well be the single most well thought out and significant of all the 32 caliber 640 designs.
First, in Old Norse, it is spelled: Mjǫllnir and is often commonly spelled Mjölnir or just Mjolnir because modern keyboards do not support Old Norse spelling. According to a professor who teaches Old Norse it is pronounced MULE-NEER and the R at the end is rolled like in Spanish.
Second, the overall length of the Mjolnir is both extremely tolerant yet bears a hidden twist of versatility. Probably the shortest cylindered 32 sixgun in common use is the Ruger Single Six. Mjolnir is going to fit those many 32 H&R sixguns out there and satisfy any heavy duty bullet chores required of those sixguns.
Third, that extra lube groove. None of the other 32 Caliber 640 designs have it. That makes the Mjolnir the best choice for a Carbine because it will surely carry enough lubricant to make it to the muzzle. Not that the other designs won't, but the additional lubricant is a failsafe. The .297" nose to crimp is the icing on the cake here as well because it practically guarantees smooth cycling in a lever gun and ammunition that will hold crimp even if stacked in a long magazine tube. More, in a sixgun, one might even use that top lube groove as a crimp groove to load this design long (This assumes throats with proper dimensions) and have more room in the parent case for powder. It would be close, but that idea might even work in the aforementioned Ruger Single Six 32 H&R magnum and allow for the ultimate load in that design envelope. It remains to be seen if the newer GP100 and SP101 can be loaded long as well with this design.
Fourth, it's perfect for the Single Seven yes, but it is also perfect for the Single Six design window itself. Consider this, The Sledgehammer is a fantastic bullet. In the 32-20 it is an absolute best with it's heavest loads in modern sixguns with tight chambers well into 357 Magnum territory. But it's too long to fit in the Single Six design envelope. That is not true of Mjolnir. A 32-20 case is supposed to be 1.315" long. The nose to crimp on Mjolnir is .297". Added together the total length is 1.612" which is just about the maximum "safe" cylinder window for a Single Six. The long bearing surface of Mjolmir may yield some very interesting ballistics from the .327 Federal and a properly chambered and modern 32-20....
Last, there are the short necked wildcat sixguns. Again, using the top grease groove as crimp groove might just get the base of the GC into the base of your case. It is definitely going to fit in the Custom Bearcats. One can only wonder if 30 Carbine and other similar cartridges might benefit. As I said in the beginning, this one is really going to be something.
4 Cavity Gas Check List
01. kellyc2215 AT msn DOT com....1 mold
02. jrayborn AT outlook DOT com....1 mold
03. fixedchokes AT yahoo DOT com....1 mold
04. ward DOT olson AT yahoo DOT com....1 mold
05. mjcrookston AT msn DOT com....1 mold
06. thadd3220 AT yahoo DOT com....1 mold
07. dragon813gt AT yahoo DOT com....1 mold
08. wonderwolf AT gmail DOT com....1 mold (request penta pins)
09. wrichins AT gmail DOT com....1 mold
10. alamogunr AT charter DOT net....1 mold
11. longrange2 AT outlook DOT com....1 mold
12. mccabeguns AT yahoo DOT com....1 mold
13. Tippieacdo AT AOL DOT com....1 mold
14. ktlachac AT aol DOT com....1 mold
15. ggoodwin six three at yahoo.com....1 mold
16. bmsouder AT ymail DOT com....1 mold
17. rockwell5926 AT gmail DOT com....1 mold
18. dcasad AT hotmail DOT com....1 mold
19. ncrobb at bellsouth dot net....1 Mold
4 Cavity Plain Base List
01. kellyc2215 AT msn DOT com....1 mold
02. dcasad AT hotmail DOT com....1 mold
03. mjcrookston AT msn DOT com....1 mold
04. highlander338 AT gmail DOT com....1 mold (requesting penta pins)
05. haw1961 AT live DOT com....1 mold
06. dennis DOT adotulrich AT gmail DOT com....1 mold (requesting penta pins)
07. bbailey7821 AT hotmail DOT com....1 mold
2 Cavity PB List
01. ronaldmeyers AT charter DOT net....1 mold
2 Cavity GC List
01. ronaldmeyers AT charter DOT net....1 mold
02. jstahlconstruction AT yahoo DOT com....1 mold
03. gunner AT tctwest DOT net....1 mold
8 Cavity HiTek PB
01. greg AT watch mans tower DOT com....1 mold
4 Cavity HiTek PB
01. jbpaul AT suddenlink DOT net.....1 mold
02. greg AT watch mans tower DOT com....1 mold
8 Cavity HiTeck GC....1 mold
01. greg AT watch mans tower DOT com
4 Cavity HiTek GC
01. jbpaul AT suddenlink DOT net.....1 mold