RotoMetals2WidenersInline FabricationTitan Reloading
RepackboxGraf & SonsMidSouth Shooters SupplyStainLess Steel Media
Lee Precision
Results 1 to 9 of 9

Thread: Propane forge for Father's Day :)

  1. #1
    Banner Sponsor

    lar45's Avatar
    Join Date
    Mar 2005
    Location
    Arkansas
    Posts
    1,341

    Propane forge for Father's Day :)

    The wife got me a propane fired forge for Father's Day.
    Click image for larger version. 

Name:	forge-01.jpg 
Views:	59 
Size:	25.4 KB 
ID:	223269
    The only steel I had on hand was some 3/4" round mystery metal. I was anxious to get started on something, so I chopped off a piece and started hammering.
    Click image for larger version. 

Name:	blade-01.jpg 
Views:	53 
Size:	84.0 KB 
ID:	223270
    This is after the blade was roughed out. The blade turned out to be about 7", so I cut an inch off and reshaped it.
    Click image for larger version. 

Name:	knife-02.jpg 
Views:	56 
Size:	56.2 KB 
ID:	223271
    We cut down a Cedar tree last spring and I cut the handles out of one of the branches.
    Now I just need to see if I can put an edge on it.
    I ordered some 1080, 5160 and 52100, so I'll have something better to try on the next one.

  2. #2
    good job!!!!!!
    "Where We Go One, We Go All!!!
    We The People!
    From Sea to Shining Sea.
    Let Freedom Ring, Patriots.
    It Is Your Time.
    If America Falls, The World Falls.
    United We Stand!
    God Bless You All."

    Q+

    WE ARE Q!!!!!!

    Deplorable Dregs

  3. #3
    Vendor Sponsor
    Handloader109's Avatar
    Join Date
    Jan 2014
    Location
    NW Arkansas
    Posts
    1,262
    Looks good... enjoy

    Sent from my SM-G892A using Tapatalk

  4. #4
    Boolit Master
    CastingFool's Avatar
    Join Date
    Mar 2009
    Location
    Climax, Michigan
    Posts
    1,603
    Looks like a very nice job. I would like to try making my own forge, but right now, it's just a pipe dream. Too many other things have to be taken care of first.

  5. #5
    Boolit Master




    Bzcraig's Avatar
    Join Date
    Dec 2012
    Location
    Nampa, ID
    Posts
    3,686
    Nice..
    "Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same......." - Ronald Reagan

    "It is foolish and wrong to mourn the men who died. Rather, we should thank God that such men lived." - George Patton

    The second amendment is a nail on which hangs a picture of freedom - member Alex 4x4 Tver, Russia

  6. #6
    Boolit Bub dbmjr1's Avatar
    Join Date
    Aug 2012
    Location
    NOLA
    Posts
    46
    Being mystery metal, you can get an idea of how hard it is with a file.

    If it's seems soft, you might try hardening the edge of the blade by heating it with a torch, then quenching in oil.
    "Those who would give up essential Liberty, to purchase a little temporary Safety, deserve neither Liberty nor Safety."
    ~Ben Franklin

  7. #7
    Banner Sponsor

    lar45's Avatar
    Join Date
    Mar 2005
    Location
    Arkansas
    Posts
    1,341
    After the blade was mostly finished, I heated it up to non-magnetic and quenched in a bucket of tractor Hydraulic oil(I accidentally bought the wrong type, so it was just sitting there and I couldn't use it for anything else). Then put it in the oven at 450 for and hour to temper it.
    I browsed some of the knife making forums and it looks like the oil that most of the guys use is Canola oil heated up to 135F. I saw that one of the forums has a section called Knife Making 101, so it looks like I have a bunch of reading to do before I finish the next one.

  8. #8
    Boolit Buddy
    Join Date
    Dec 2005
    Location
    R.I.
    Posts
    246
    If you have any truck repair shops around check for old leaf and coil springs for your
    steel. I go to the spring shops around here and they will give you scrap pieces if you
    ask. This is air hardening steel and will make nice knife blades. I try and get the spring
    scrap used for small boat trailers as it is a nice size to work with. Old shock absorbers
    work well too. As well as the railroad track clips that hold the ribbon track down. Scrap
    yards are your friend for good steel cheap.
    webfoot10

  9. #9
    Super Moderator & Official Cast Boolits Sketch Artist


    RP's Avatar
    Join Date
    Mar 2008
    Location
    Nahunta NC
    Posts
    2,916
    Great job I been playing with smelting alum and casting it into billet to use in my lathe for practice. I started out with a oil fired homemade burner but man it was a job getting it running and then it was so hot I was burning my steel pot to the point of failure. I took some time off work and built me a LP gas jet burner its hot and easy to control just not hot enough so I am going to add one more to the pot. I did melt some old brass scrap I had on hand and cast some nice ingots that I cleaned up and they look like little gold bricks lol. This is my new project and I am loving it I want to build a forge for working steel like you are it is such a great way to make things for yourself. I really want a anvil but the good ones will cost you so for right now I am just working on building up my gear so one day I can make things like a blacksmith.
    My problem is to many projects not enough time or money lol
    Reloading to save money I am sure the saving is going to start soon

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check