I have several molds for 45/70 from Saeco,RCBS and NOE from 300 t0 525 gr. In your Ruger No 3 300 to 400gr will be the most comfortable with trapdoor loads. Size bullets .458,.459 powders to use 3031,RL 7,4227,5744 and for laughs black powder or it's substitutes. As far as the alloy to use wheelweights,1pt sn to 20 pts pb or anything up to Lyman no 2.
400gr+/- would be my preference. I have only used cheap molds in the past and I plan to order one from Tom at accurate molds. Just want to get one that "fits the gun well." The first try.
I'd try the lighter bullets first the No 3 isn't all that heavy and the steel butt plate will beat you into submission in short order. Order some cast bullets from Missouri Bullet Co in different weights to figure out which bullet weight works the best without dislocating your shoulder. I've had several No 1s and they weigh a good 2 lbs heavier and with borderline 458 mag loadsthey were a handful.
Last edited by DocSavage; 06-16-2018 at 06:34 PM.
I've used the lee 405 plain base and like it loaded with trail boss its a great pinker and with a stout load of 3031 it will make any "cool guy" shut his mouth. I was getting bad leading with that boolit I believe it was due to poor fit as it dropped at .457"
I'm mostly looking for designs that may perform better as far as accuracy and fit well to prevent leading.
I don't have an answer to your questions, but I'm gonna guess that those details aren't as crucial when loading for 45-70 at "less than High Velocity". Now, if you are looking for great accuracy at long distances with Max loads, then I suspect you will need to know more details than those dimensions that are shown in the image. Here are a couple of older threads that may provide some of that type of insight.
http://castboolits.gunloads.com/show...roove-diameter
http://castboolits.gunloads.com/show...765-Throat-fit
-----------------------------
But, your could just consult with Tom, as you spec'd him as your custom maker, He'll probably have your best answers...and more questions for you to answer. I believe email is the best way to contact him.
----------------------------
Since others are offering what they use... I cast the NOE 460-405 FN for my Ruger #3, I size to .459
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
Does that wide meplat bullet do well at longish distance say 200 yards?
I use this: http://www.accuratemolds.com/bullet_...=46-400M-D.png and size it to .459 out of my original Winchester 1886 that slugs at .458. I have no issues what so ever. I also use a PB gas check made out of soda/beer cans with dies from Pat Marlin: https://www.patmarlins.com/product/45pbr-rifle-cal/. Hope this helps.
So I ordered a .459" sizing due and I am gonna size a bullet and insert it backwards into the case an see how far out it will chamber. Thank you all for the replies.
I may try a slightly modified version of the 46-405v
that may very well work, but I set COAL by trial and error, making dummy rounds, starting about as long as possible, then attempt to chamber the dummy, if it's no-go, which is usually the case, I keep trying shorter lengths, until I find the length that chambers, but the rifling still makes witness marks on the boolit's nose.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
Do you adjust case length to accommodate crimp groove or just not worry about the crimp groove?
I don't worry about the crimp groove. Mostly I don't crimp, I will use the crimp die to remove the flair.
~~~~~~~~~~~~~~
“If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
― The Dalai Lama, Seattle Times, May 2001
I spoke with Tom and decided on the .46-345A mold. Does anyone have this mold ?
http://www.accuratemolds.com/bullet_...=46-345A-D.png
I use the lee 420 gr El Cheapo mold. Bullets are shot as cast over 15 grs. of Unique with
a wad of toilet paper on the powder. I don't size just lube and load. I use the old Lee
hand loader to load the 45/70 cases. This load in my #3 will take the ten ring out
at 100 yds. 15 grs of Unique or 3031 will both shoot to poa at 100 yds. Shoot the
#3 Ruger with as large a dia. as will chamber. Try it you'll like it.
The mold drops a little over .462"i will try one as cast but I doubt it will chamber.
I had a lee 405gr but it dropped too small. I tried leementing it but I screwed it up.
I have 50 loaded with 12.5gr of unique to try. I may go higher. Does the toilet paper make much of a difference for you?
I only use the toilet paper as a filling to hold the powder down on the primer. The toilet paper
just blows apart when fired. I figured that 15 grs of Unique would just spread out over the
length of the case and could cause SEE condition and pressure spike. Others here might have
more information. I never tried the Unique or 3031 load without a filler.
webfoot10
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |