Lee PrecisionADvertise hereRotoMetals2Titan Reloading
Inline FabricationGraf & SonsMidSouth Shooters SupplyStainLess Steel Media

Results 1 to 8 of 8

Thread: My Pro Melt is Going Back for Service

  1. #1
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258

    My Pro Melt is Going Back for Service

    I have a 2 year old Pro Melt. I'm pretty sure that the thermostat is faulty. At a setting of 725, it has been swinging +/- 50 degrees or more. Dipping down to 650 then climbing to 800. Once, it did not cycle at all and suddenly the spout was frozen. The weird thing is that if it is running hot or cold (where I know it should cycle on/off) and I adjust the knob barely, it responds. I keep the pot between 1/4 and 3/4 full typically.

    There is definitely something not right. I am literally 2 days away from my warranty end. Lucky! I spent the day casting a bunch of bullets, then drained the pot.

    I'll ship it tomorrow or Tuesday. The rep at RCBS said to send it in, or they would just mail a thermostat to me with instructions for how to drill out the rivets and to re-wire it. I'd like them to do the work. Apparently if it is out of warranty, they'll send a thermostat anyway. Great service!

    I've considered skipping the warranty work and going straight to PID, but thought I'd at least get it in good working order before the warranty is gone.

  2. #2
    Boolit Master
    Join Date
    Jun 2016
    Location
    SoCal
    Posts
    165
    Good choice. I just sent my 35yr old back for the 2nd time 3 months ago. This time they charged me $111.00 for a full rebuild. And $30 bucks to send it to them. The temp. keep bouncing up&down, froze the spout once. So I figured to get it in while they still had parts to work on it.

    So they offered to tell you how to drill out the rivets, and send you a new thermostat with instructions on how to install it. That really interests me. i'd like to find out how to do that and install a PID.
    Happiness is a Warm GUN & more ammo to shoot in it.

  3. #3
    Boolit Master dikman's Avatar
    Join Date
    May 2013
    Location
    Sth Oz - A Land Downunder
    Posts
    1,816
    Walks, if you're fitting a PID all you need to do is plug the pot into the PID, turn the thermostat to max and leave it there.

  4. #4
    Boolit Master
    Join Date
    Jun 2016
    Location
    SoCal
    Posts
    165
    dikman,
    i have no experience with PID's, never having seen one up close. I've seen them in a video. Dude drilled a hole in the back of his LEE pot & stuck the probe through the hole to rest on the heating element underneath the pot. Guess I should have looked at more video's. I keep seeing guys putting them together, but I'm electronically challenged & broke. Don't even own a soldering iron. Still confused by the process.
    Happiness is a Warm GUN & more ammo to shoot in it.

  5. #5
    Boolit Master


    Walter Laich's Avatar
    Join Date
    Aug 2005
    Location
    Cypress, Republic of Texas
    Posts
    2,943
    I've opened mine twice

    when drilling out the rivets be sure to keep it from spinning. I used needle nosed pliers to hold it while I drilled. Go easy as you don't want to have the drill go all the way up to the chuck when you finally drill the center out (it really is an easy job. Once you get all four drilled out the top and bottom come apart.

    I considered using sheet metal screws to reassemble but wanted to play with my pop rivet gun so I went that route.
    NRA Life
    USPSA L1314
    SASS Life 48747
    RVN War Games, 2nd Place

  6. #6
    Boolit Master dikman's Avatar
    Join Date
    May 2013
    Location
    Sth Oz - A Land Downunder
    Posts
    1,816
    Walks, there are lots of threads/posts on here about PIDs, best thing is to start reading them, that's what I did (I'd never heard of them until I joined this site!).

  7. #7
    Boolit Master
    Mal Paso's Avatar
    Join Date
    Jun 2010
    Location
    Carmel, Ca
    Posts
    1,866
    I found a sharp wood chisel will shear the aluminum rivet's head off easier than drilling.
    Mal

    Mal Paso means Bad Pass, just so you know.

  8. #8
    Boolit Master
    Join Date
    Mar 2005
    Posts
    3,389
    If you can figure out who made the thermostat by looking at the logo you can call them and they might send you several engineering samples.
    Lid switche for my washer failed and a new one was $15. New from the OEM they were $1.75 but they senothing.samples for nothing.
    EDG

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check