Smelting some pewter and I got a big eruption. I was wearing safety gear, but some splotches got out past the tarp and landed on the concrete of the patio I was set up on. Any easy way to get it off the concrete surface? Wire brush?
Smelting some pewter and I got a big eruption. I was wearing safety gear, but some splotches got out past the tarp and landed on the concrete of the patio I was set up on. Any easy way to get it off the concrete surface? Wire brush?
When you care enough to send the very best, send an ounce of lead.
A sharp pick of some sort should work best. Our downstairs concrete deck has small pebbles embedded in the surface of the concrete and the pick works well. Nice thing is that as lead ages, it gets darker and ends up about the same color as concrete. Big Boomer
I have used a razor scraper to get under it and pry/lift it up. Royal pain.
Yeah...I wouldn't try to "scrub" it...try to lift corners and pull it off. It likely had some cooling before it hit so it shouldn't have been able to get too deep into the pores of the concrete.
redhawk
The only stupid question...is the unasked one.
Not all who wander....are lost.
"Common Sense" is like a flower. It doesn't grow in everyone's garden.
If more government is the answer, then it was a really stupid question. - Ronald Reagan
I have a chisel. Ones you pop a corner up, then it will peel up easily enough. Just let it cool first then pry it up.
Sent from my SM-G925T using Tapatalk
"Speak softly and carry a big stick; you will go far."
~Theodore Roosevelt~
I used a power washer.
agreed, it won't stick like gum, it merely has a hand hold in the pores of the material. it should pry up easily.
Glad you were not hurt. I use a putty knife about 1 inch wide. Like a chisel. Not from the Ferry but from the slops and drips from smelting. Like the others said, you peel a corner up and it comes right off.
Glad I wear a.full face shield. I would have gotten it right in the pie hole.
When you care enough to send the very best, send an ounce of lead.
Funny you should mention this. Out of the 50 or 60 aboard a I have melted, the last one I did, the melt popped after I threw in the handle.
Luckily I was do I g it in my sheds would burning stove at the time. Have to remember to sift the ashes next time I clean.
This should come off easily. I'd whack it with a pressure washer.
Pressure washer took care of my few spots in the garage. Easy peasy, they peal right up and go back in the pot.
My feedback page if you feel inclined to add:
http://castboolits.gunloads.com/show...raight-Shooter
Thanks Yall!
Large pieces pull right up. Small pieces respond well to a pressure washer
At one with the gun.
I would like to see a video of a tinsel fairy.
I've always just hit it with a little soldering torch and the heat usually causes it to pull itself into a tiny ball.
I usually just use a flat headed screwdriver or old knife. For larger globs that somehow make their way to the floor when making ingots I pinch them with a pair of pliers and they pull right up
Try one of those keyboard dust blower cans that use a compressed gas. Turn it upside down when spraying and the thermal contraction should bust it loose. It also is good for small dents ic sheet metal as well as removing drippage from candels
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |