Lee PrecisionRepackboxInline FabricationADvertise here
WidenersMidSouth Shooters SupplyTitan ReloadingRotoMetals2

Page 1 of 4 1234 LastLast
Results 1 to 20 of 73

Thread: ACTIVE - MiHec 8mm Sil Rerun 2 & 4 Cavity HP / 6 & 8 Cavity Solid

  1. #1
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784

    ACTIVE - MiHec 8mm Sil Rerun 2 & 4 Cavity HP / 6 & 8 Cavity Solid

    Miha is giving the green light on this mold for a rerun.

    Thank you to the designer and all past participants in the last buy!

    MiHec 8mm Sil brass
    This is a sign-up thread for an old GB & BRP mold design........ specifically a heavier cast boolit for the 8mm caliber rifles. This boolit is a gas check design. It casts out slightly above 0.326" and sizes easily to 0.324". Ready to load weight is about 200 gr. dependent on your alloy. It has fit in everything we've tried it in. To date the best load has gotten sub 1 MOA at 100 yds....... due to lack of a good scoped rifle.

    The costs will be as follows-

    - 2 Cavity HP all pins included 95 Euro's (80,75 with discount)
    - 4 Cavity HP all pins included 135 Euro's (114,75 with discount)
    - 6 Cavity solid Brass (80,75 with discount)
    - 8 Cavity Aluminum (80,75 with discount)

    Prices and options are to be confirmed by MiHec they may change!

    Please give your disguised e-mail address and the number and type of molds you want.

    As always these buys can take time please be patient and give grace. Getting upset will not make it go any faster!

    The discussion thread is here: http://castboolits.gunloads.com/show...27#post1603627

    Attachment 216873Attachment 216874
    Last edited by Wasalmonslayer; 03-22-2018 at 11:18 AM.

  2. #2
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Sign up List

    Solid Molds-

    1) kawacharles1973 at gmail dot com - 6 Cavity Brass
    2) Shawn smc at hot mail dot com - 8 Cavity Aluminum
    3) Jay Aich at Hammer Bek dot com - 8 Cavity Aluminum
    4) lattanzizxc att gmail dot com - 6 Cavity brass
    5) zipporaider1968 at yahoo dot com - 6 Cavity Brass
    6) r dot nittritz at telus dot net - 6 Cavity Brass
    7)
    8)
    9)

    HP Molds

    1) scottturknett at hotmail dot com - 4 Cavity HP
    2) shutupandjump at yahoo dot com - 4 Cavity HP
    3) lattanzizxc at gmail dot com - 2 Cavity HP
    4) kc5vtk at comcast dot net - 4 Cavity HP
    5)
    6) ckulyk at telus dot net - 4 Cavity HP
    7) Jay Aich at Hammer Bek dot com - 4 Cavity HP
    8) zacalldredge at gmail dot com - 2 Cavity HP
    9) adamjsmith80 at gmail dot com - 4 Cavity HP
    10)
    Last edited by Wasalmonslayer; 07-25-2019 at 03:42 PM. Reason: K

  3. #3
    Boolit Bub bns454's Avatar
    Join Date
    Mar 2016
    Location
    Anoka MN
    Posts
    74
    Is there a drawing somewhere with sizes showing the nose diameters/profile ?
    One who does nothing makes no mistakes.

  4. #4
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by bns454 View Post
    Is there a drawing somewhere with sizes showing the nose diameters/profile ?
    I just attached a couple of photo's

  5. #5
    Boolit Bub Uncle Dave's Avatar
    Join Date
    Jul 2017
    Location
    St Charles, Mo.
    Posts
    61
    Your opinion please - would this be a good mold for both 8mm (Mauser) and 32 WS (94 Win) with the appropriate sizing of course? The picture of the flat nose or hollow point MIGHT make it safe for tube feed rifles. Any actual experience anyone?
    Thanks
    Uncle Dave

  6. #6
    Boolit Bub bns454's Avatar
    Join Date
    Mar 2016
    Location
    Anoka MN
    Posts
    74
    Quote Originally Posted by Wasalmonslayer View Post
    I just attached a couple of photo's
    I worded that wrong,Sorry.Can we know the approximate diameters as cast after that front drive band.
    One who does nothing makes no mistakes.

  7. #7
    I'm in: (1) 6 Cavity solid Brass mold.

    kawacharles1973 at gmail dot com

  8. #8
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by bns454 View Post
    Is there a drawing somewhere with sizes showing the nose diameters/profile ?
    I messaged Miha to see if we could get a few specs.

  9. #9
    Boolit Bub bns454's Avatar
    Join Date
    Mar 2016
    Location
    Anoka MN
    Posts
    74
    Thank You !
    One who does nothing makes no mistakes.

  10. #10
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by Uncle Dave View Post
    Your opinion please - would this be a good mold for both 8mm (Mauser) and 32 WS (94 Win) with the appropriate sizing of course? The picture of the flat nose or hollow point MIGHT make it safe for tube feed rifles. Any actual experience anyone?
    Thanks
    Uncle Dave
    Good morning
    I have no personal experience with either of them but maybe someone else will chime in to help out.
    I do know it may be a little sketchy in the win 94 tube just for reasons with the bullet being pushed back in the case.
    You would have to do a decent crimp to get it to hold.

  11. #11
    Boolit Buddy shawnsmc's Avatar
    Join Date
    Dec 2010
    Location
    Morgan Hill, CA
    Posts
    207
    I'm in for an 8 cavity. Shawn smc at hot mail dot com
    "(The Constitution preserves) the advantage of being armed which Americans possess over the people of almost every other nation...(where) the governments are afraid to trust the people with arms." -James Madison

  12. #12
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by shawnsmc View Post
    I'm in for an 8 cavity. Shawn smc at hot mail dot com
    Got you on the list

    Thank you!

  13. #13
    Boolit Master


    HangFireW8's Avatar
    Join Date
    Dec 2008
    Location
    Central Maryland
    Posts
    2,520
    6 Cavity solid Brass
    hang fire w8 atttttt gmail dot com
    I give loading advice based on my actual results in factory rifles with standard chambers, twist rates and basic accurizing.
    My goals for using cast boolits are lots of good, cheap, and reasonably accurate shooting, while avoiding overly tedious loading processes.
    The BHN Deformation Formula, and why I don't use it.
    How to find and fix sizing die eccentricity problems.
    Do you trust your casting thermometer?
    A few musings.

  14. #14
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by HangFireW8 View Post
    6 Cavity solid Brass
    hang fire w8 atttttt gmail dot com

    Got you down

    Thanks!

  15. #15
    Boolit Mold
    Join Date
    Aug 2015
    Posts
    9
    lattanzizxc att gmail dot com 6 cavities brass
    PS New at group buys, please do inform me as to further steps to be taken... Thanks!
    Polo

  16. #16
    Boolit Bub
    Join Date
    Jul 2010
    Location
    Right here
    Posts
    64
    sign me up for a - 6 Cavity solid Brass. zipporaider1968 at yahoo dot com
    What is happiness "To crush your enemies, see them driven before you, and to hear the lamentations of their women!"
    Conan the Barbarian

  17. #17
    Boolit Bub
    Join Date
    Oct 2016
    Location
    Eagle River, AK
    Posts
    58
    I will take a 4 cavity
    scottturknett at hotmail dot com

  18. #18
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by pistol View Post
    lattanzizxc att gmail dot com 6 cavities brass
    PS New at group buys, please do inform me as to further steps to be taken... Thanks!

    Got you on the list.
    Now we wait. Nothing else required till Miha mills them and sends you a paypal invoice.

    Thank you!

  19. #19
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by 5 RING View Post
    sign me up for a - 6 Cavity solid Brass. zipporaider1968 at yahoo dot com
    Got you fixed up

    Thank you

  20. #20
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    1,784
    Quote Originally Posted by AlaskaScott View Post
    I will take a 4 cavity
    scottturknett at hotmail dot com


    4 Cavity hp??
    If you want a solid mold it will be a six cavity brass or 8 cavity aluminum.

    Please advise

Page 1 of 4 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check