ADvertise hereLee PrecisionMidSouth Shooters SupplyTitan Reloading
StainLess Steel MediaGraf & SonsRotoMetals2Inline Fabrication

Page 2 of 2 FirstFirst 12
Results 21 to 37 of 37

Thread: First H&G 2 Cavity Mold, Need Some Help

  1. #21
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258
    Quote Originally Posted by jsizemore View Post
    Don't hit the sprue plate to remove the sprue!!!!!!
    I like to turn them by hand.

  2. #22
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258
    Progress!

    Evaporust. Man, that stuff is handy. After a 1/2 day soak and some work with Dawn soap and a toothbrush, the cavities are looking pretty good. The metal was looking parched after the de-rust operation, so everything got a coat of Ballistol for storage while I figure out the handle situation. In my experience, Ballistol cleans out of the cavities pretty easily.

    I fixed the retention screw heads by taping the threads with painters tape and lightly chucking in a drill. I spun the perimeter of the screw heads on sandpaper to remove a teansie bit of radius. They are now able to turn deep enough into the block to reach the sprue pivot and stop screws.

    Next up:

    remove lead from the cavity faces, and
    contact NV Ballistics that JonB referenced for handles (thanks JonB!).

    Last edited by Taterhead; 03-19-2018 at 01:15 PM. Reason: typos

  3. #23
    Boolit Master

    Join Date
    Oct 2009
    Location
    England,Ar
    Posts
    3,378
    It good to see that you are getting that nice old mold back into useable condition. The H&G molds that I have are a pleasure to cast with.

  4. #24
    Boolit Master
    Join Date
    Jul 2008
    Posts
    2,633
    Quote Originally Posted by Taterhead View Post
    I like to turn them by hand.
    If you watch the video posted by skeettx the guy hits the sprue plate after it's open. Don't do that!!!

  5. #25
    Boolit Master Harter66's Avatar
    Join Date
    Jan 2010
    Location
    Walker Lake Nv. or just about 5 miles west of the exact middle of nowhere.
    Posts
    4,148
    Quote Originally Posted by skeettx View Post
    That is an awesome solution for the sprue plate !
    I have been white noise thinking about how to go about getting a 3rd handle on the plate .
    In the time of darkest defeat,our victory may be nearest. Wm. McKinley.

    I was young and stupid then I'm older now. Me 1992

    About that rally point, the soap and mail boxes fall on blind eyes and deaf ears,the ballot box is manipulated,it would seem we are fast running out options....

  6. #26
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258
    Quote Originally Posted by jsizemore View Post
    If you watch the video posted by skeettx the guy hits the sprue plate after it's open. Don't do that!!!
    Oh yes, I see what you're talking about, and I agree.

  7. #27
    Boolit Master
    Dragonheart's Avatar
    Join Date
    Jan 2012
    Location
    Katy, Texas
    Posts
    1,288
    Taterhead, if you want to send me the mold I will see if I can cut some screws for it. I have replaced the screws on my H&G molds with stainless. I do keep all the original H&G screws, but I am not a collector. I use my molds so the stainless works better for me, especially changing out the proud screws on the bottom of some of the 4 cavity molds with screws that are flush.

    Or if you can give me precise measurements I may be able to make it work.

  8. #28
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258
    Quote Originally Posted by Dragonheart View Post
    Taterhead, if you want to send me the mold I will see if I can cut some screws for it. I have replaced the screws on my H&G molds with stainless. I do keep all the original H&G screws, but I am not a collector. I use my molds so the stainless works better for me, especially changing out the proud screws on the bottom of some of the 4 cavity molds with screws that are flush.

    Or if you can give me precise measurements I may be able to make it work.
    Oh, man! That's a great offer. Since I have all the screws working, I'll go ahead and run with it for now. VERY much appreciated.

  9. #29
    Boolit Master
    Dragonheart's Avatar
    Join Date
    Jan 2012
    Location
    Katy, Texas
    Posts
    1,288
    To remove the lead from the mold face mix 50/50 ratio of standard 3% hydrogen peroxide and white vinegar. Apply the solution with a Q-tip and rub with a pencil eraser dipped in the solution. It may take you a few minutes, but the lead will dissolve. Then lube the mold surface as this solution is a super oxidizer and will cause rust. BTW: This is a very old solution for removing lead from a gun barrel. It will also add a patina to brass molds almost instantly.

  10. #30
    Boolit Master

    Join Date
    Nov 2011
    Location
    East Arkansas
    Posts
    315
    Quote Originally Posted by jsizemore View Post
    Don't hit the sprue plate to remove the sprue!!!!!!
    The instruction that came with Hensley & Gibbs molds states that the use of a lead hammer is the preferred method of opening a sprue plate.
    On 6 and 8 cavity molds this is a must. There are instructions on this site on how to make them. Classic sticky section.

  11. #31
    Boolit Master
    Join Date
    Jul 2008
    Posts
    2,633
    Quote Originally Posted by LenH View Post
    The instruction that came with Hensley & Gibbs molds states that the use of a lead hammer is the preferred method of opening a sprue plate.
    On 6 and 8 cavity molds this is a must. There are instructions on this site on how to make them. Classic sticky section.
    I didn't say don't use a hammer, mallet, stick, thumb, whatever to open the sprue plate, I'm saying, DON"T HIT THE SPRUE PLATE AFTER IT'S OPEN. Got it?

  12. #32
    Boolit Bub
    Join Date
    Oct 2007
    Location
    Struthers,Ohio
    Posts
    33
    I had a mold that resembled the one in the picture purchased at a garage sale. I soaked it in WD-40 then got a bore bruch wrapped in fine steel wool and
    ran it in each cavity until clean. I then polished the cavities with rubbing compound on a clean mop. The mold casted perfect bullets after that. I heavily smoked
    all cavities before casting.

  13. #33
    Boolit Master

    Join Date
    Nov 2011
    Location
    East Arkansas
    Posts
    315
    Yep only the handle bolt.

  14. #34
    Boolit Master
    Join Date
    Mar 2016
    Location
    Boise, Idaho
    Posts
    258
    A little more progress. Modified a set of Lee 6 cavity handles by grinding them thinner. Pretty crude workmanship on my part, but seems serviceable. The location of the holes and diameter are good without modification.

    The wood handles are already trying to slip off so I'll need to secure them with pins.

    Now just need to figure out how to get lead off the mold faces, then should be ready to go. This old thing is growing on me. Such much for the project I didn't want!

    Tomorrow looks good to warm up the furnace. I'll report back with some boolits pics.


  15. #35
    Boolit Master
    Dragonheart's Avatar
    Join Date
    Jan 2012
    Location
    Katy, Texas
    Posts
    1,288
    Read my previous post as to removing lead from the mold. Rubbing with the pencil lead in addition to the pencil eraser kept wet with the solution will help exposing new surface area for the solution to dissolve. As I said it is not super fast but it will remove all the lead, especially in the vent grooves and at the edge of the cavities where the lead tends to form. Do not be tempted to put the mold faces to a wire wheel, a wire wheel works fine for the exterior sides and bottom of a mold, but not on the cavities as it will round the surface edges.

  16. #36
    Boolit Master



    Join Date
    Dec 2005
    Location
    Southwestern Ohio
    Posts
    8,128
    I have a four cavity H&G #50 mold that I dearly love! That is an EXCELLENT w/c bullet for .38ís. Right now, that is one of my most used bullets.

    FWIW
    Dale53

  17. #37
    Boolit Master
    Dragonheart's Avatar
    Join Date
    Jan 2012
    Location
    Katy, Texas
    Posts
    1,288
    The great thing for those that still load & shoot 38 is the #50 H&G had to be the mold they sold the most of because now you can find a really nice #50 dirt cheap, considering the quality of these molds.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check