StainLess Steel MediaMidSouth Shooters SupplyTitan ReloadingRepackbox
Graf & SonsInline FabricationWidenersRotoMetals2
Lee Precision
Results 1 to 4 of 4

Thread: 45LC Shotshells for 303 British???

  1. #1

    45LC Shotshells for 303 British???

    Would like to make some shotshells for 45LC. The problem is the Ruger New Model Valquero cyclinder is not bored full diameter all the way through. It is like the forcing cone is in the cylinder, not in the frame before the barrel.

    With this, I can not simply use a longer brass cartridge, such as a 454 Casull or 460, or even a cut-down 410 hull.

    I've heard of fire forming 303 British, but I would have to cut down, trim, etc.

    So how can I cut, trim to length, fire form and load the "tapered" casing???

    Why....because I can (or want to)

  2. #2
    Boolit Grand Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    6,181
    Use the Starline 5 in 1 blank cases. These work for shot loads in .38-40, .44-40, .44 Magnum, .45 Colt, and .454 Casull.

    The cases come tapered already to fit down a .38-40.

    In .44 Magnum and up you want to expand with a .44-40 or .44 Mag expander plug to make cylindrical.

    Keep powder charge light due to large flash hole. 5 grains of Bullseye is correct.

    Insert Buffalo Arms .44 card over powder and seat with 3/8" dowell.

    Then insert Federal 410SC shotcup over the card wad. Absolutely necessary not to omit the card wad because the .410 shotcup is too small in diameter to seal in the .44 case and is powder leaks past the .410 shot cup it will cause "bloopers" and possibly leave wad in barrel as bore obstruction!

    Seat shotcup firmly onto over-powder card then fill with fine shot No.8 or smaller to case mouth. Place .36 cal. Walters wad card over shot. Crimp in .44 Game Getter or .45 ACP Shot die, then trim protruding wad fingers flush to case mouth with sharp knife.

    These rounds properly loaded will withstand rough handling and feed through Winchester and Marlin lever actions. In a rifled barrel they kill small game to 25 feet. In a smoothbore .410 or Marble Game Getter they are killing loads to 50 feet.

    Attachment 215448Attachment 215449Attachment 215451Attachment 215460Attachment 215453Attachment 215455Attachment 215459Attachment 215461Attachment 215462Attachment 215463

    The .45 Colt patterns here are of "Shot and Ball" Game Getter load with .390" round ball crimped in end of shell instead of .36" top card. Ball impact is marked on target.
    Last edited by Outpost75; 03-01-2018 at 12:49 AM.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  3. #3
    Boolit Master
    NoZombies's Avatar
    Join Date
    May 2009
    Location
    N. Florida
    Posts
    2,153
    You can also run a 460 S&W round into a .44 mag sizer far enough to clear the constriction, and trim to a hair under cylinder length.
    Nozombies.com Practical Zombie Survival

    I collect all things .32. If you have something you don't need, please let me know!

  4. #4
    Boolit Grand Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    6,181
    Only able to post ten pictures with post, so here are pics of patterns of 5 in 1 No.8 shot vs. factory 1/2 oz. No. 6 shot in cylinder bore .410 and in a rifled Marlin 1894S .44-40:

    Attachment 215464Attachment 215465

    D1C repair center is 10 inches square.
    Inner circle is 4"
    Outer circle is 8"

    I define "killing" pattern as number of pellet hits in center 4" circle equal to or greater than shot size, such as 8 No. 8s, nine No. 9s, etc. Because ranges of handgun shot loads are short, there is no point to using larger shot which result in thinner patterns due to low pellet count.

    No. 8 shot at 25 FEET penetrate as well on rabbits, etc. as No. 6s do at 25 YARDS from a .410 bore.
    Light charges pattern better with handgun shot loads. Velocities higher than 800 fps aren't necessary within 25 ft.
    Last edited by Outpost75; 03-01-2018 at 12:54 AM.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check