Lee PrecisionInline FabricationLoad DataWideners
RotoMetals2Reloading EverythingMidSouth Shooters SupplyRepackbox
Titan Reloading
Page 1 of 2 12 LastLast
Results 1 to 20 of 27

Thread: De-Rusting the cavities of an H&G mould

  1. #1
    Boolit Master FISH4BUGS's Avatar
    Join Date
    Jun 2005
    Location
    Inland from Seacoast New Hampshire
    Posts
    2,744

    De-Rusting the cavities of an H&G mould

    I just bought an H&G 8 cavity mould "as is". I bought it CHEAP so I thought it might make a great "project"mould. It was pretty rusted at some point in its life....probably not all that long ago.
    First, it is all there. Handles are solid. It seems to close tightly with no serious hangups on the alignment pins. Unfortunately the guy I bought it from had taken a wire wheel to the outside of the mould.
    For that act of heresy may he burn in hell for an eternity.....but it is what it is. I can live with a bright shiny outside of a mould.
    Here is the problem: there are a few cavities that have a very light rust in them. Nothing serious but the surface rust is there.
    I'd like to do something to remove the surface rust (again, very light) in those places where it exists.
    I am soaking the cavities in WD40 to soften the rust.
    Any suggestions on how to best remove this rust? I'm willing to put in the time to do it a slowly and do it right.
    If I succeed, I will have a (hopefully) great casting mould.
    Tips and tricks would be most appreciated.
    Collector and shooter of guns and other items that require a tax stamp, Lead and brass scrounger. Never too much brass, lead or components in inventory! Always looking to win beauty contests with my reloads.

  2. #2
    Boolit Man
    Devon's Avatar
    Join Date
    Dec 2016
    Location
    Oklahoma
    Posts
    81
    Electrolysis gets my vote. I used it to de-rust a huge Wilton vise that I found buried in a flower bed. Weighs over 100 pounds. It took a large tank. A mould would be easy peasy. Do a google search for instructions.

  3. #3
    Boolit Master
    farmerjim's Avatar
    Join Date
    Nov 2012
    Location
    St. Francisville, Louisiana
    Posts
    1,925
    I used toothpaste and a toothbrush and light brushing on an old Lyman 4 cavity.
    Dried it up and started casting. It casts boolits as good as the day I got it 55 years ago.
    There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand

  4. #4
    Boolit Bub darrondb's Avatar
    Join Date
    Apr 2016
    Location
    NE KS
    Posts
    74
    Evaporust. Great stuff for light rust.

  5. #5
    Boolit Master

    Join Date
    Mar 2011
    Location
    oklahoma
    Posts
    2,479
    Evaporust should work. Available frim walmart and harbor freight.

  6. #6
    Boolit Grand Master

    Join Date
    Oct 2009
    Location
    England,Ar
    Posts
    7,687
    I just used Evaporust on some neglected dies. It worked as advertised but it will remove blueing. I probably would start with some Kroil and a tooth brush. Thankfully that previous owner did not use his wire brush on the inside! Good Luck in making this mold work again!

  7. #7
    Boolit Grand Master In Remembrance
    Join Date
    Aug 2005
    Location
    South Jersey
    Posts
    6,314
    there are a few cavities that have a very light rust in them. Nothing serious but the surface rust is there.
    A 50:50 mix of ATF and Acetone
    Let soak to loosen the rust and then scrub with a brass brush
    Regards
    John

  8. #8
    Boolit Master
    texassako's Avatar
    Join Date
    Jul 2012
    Location
    North Texas
    Posts
    2,038
    You can spot treat with evaporust by using shop towel pieces in the cavities, soaked in it. I have done it to keep blueing intact.
    Back in the land of boolits.

  9. #9
    Boolit Master
    Bent Ramrod's Avatar
    Join Date
    Apr 2005
    Location
    Southern Arizona
    Posts
    4,284
    If the rust is light, with no pits, you might try boiling the mould in water. This will loosen much of the surface rust (a toothbrush helps here as well) and turn the nonremovable rust to black oxide, i.e., “rust blue.”

    Or, you can just start casting with it. The boolits might be a little “frosty” looking, but generally, IME, shoot fine. The heat of casting will also “blue” the surface rust and stabilize it. The brushing one does afterwards to clean up lead smears and spots will remove the loosened rust.

    I’ve done several moulds each way with success. Best of all, neither of these procedures will do anything negative to the mould, and if they don’t work satisfactorily, you can then go with Evaporust or Liquid Wrench and toothbrushing and take it out that way.

    Doesn’t work with the heavy rust that leaves deep pits, though. Repeated treatment with Evaporust or penetrants and brushing is the way to go there. Or, if really bad, lapping by hand.

  10. #10
    Boolit Master
    Join Date
    Mar 2005
    Location
    B.C. Canada
    Posts
    2,719
    You can soak it for two or three days in water with citric acid added. Like evaporust, this will also remove bluing.
    R.D.M.

  11. #11
    Boolit Master
    Join Date
    Oct 2013
    Posts
    510
    Absolutely use Evaporust . Perfectly safe, works in a few hours, rust just wipes off.

  12. #12
    Boolit Master
    Join Date
    Mar 2010
    Location
    Michigan
    Posts
    1,200
    If you can find one of those wooden typewriter erasers..with the little brush on one end..they work fine for mould clean up..will remove rust but will not scratch..I should have stocked up back in the 70's.

  13. #13
    Boolit Master
    texassako's Avatar
    Join Date
    Jul 2012
    Location
    North Texas
    Posts
    2,038
    Quote Originally Posted by .22-10-45 View Post
    If you can find one of those wooden typewriter erasers..with the little brush on one end..they work fine for mould clean up..will remove rust but will not scratch..I should have stocked up back in the 70's.
    Hmm, that reminds me of the bundle of bamboo my wok came with to clean it. I wonder if a bamboo skewer, possibly with the end crushed, could be used to scour the cavity of rust without scratching.
    Back in the land of boolits.

  14. #14
    Boolit Master
    Join Date
    Dec 2016
    Posts
    1,091
    I've cleaned a couple of really ugly moulds by using Kroil to soften the rust scale, then used some little scrapers made of brazing rod, I hammer them out like a little chisel and sharpen with a file, and just start scraping. The Evaporust sounds like a good product I'll have to try.

  15. #15
    Boolit Master


    Join Date
    Oct 2011
    Location
    Atlanta, NY 14808
    Posts
    2,163
    I had a Lyman round ball mold with a little rust in the cavity, I used a pencil eraser to erase the rust.
    Micah 6:8
    He hath shewed thee, O man, what is good; and what doth the LORD require of thee, but to do justly, and to love mercy, and to walk humbly with thy God?

    "I don't have hobbies - I'm developing a robust post-apocalyptic skill set"
    I may be discharged and retired but I'm sure I did not renounce the oath that I solemnly swore!

  16. #16
    Boolit Master rondog's Avatar
    Join Date
    Mar 2009
    Location
    Denver, CO
    Posts
    1,838
    I'll beadblast it for ya, if you wanna pay shipping here and back.

  17. #17
    Boolit Master
    Join Date
    Aug 2007
    Posts
    791
    I had a few molds that sprouted some surface scale some time back. The ones with light surface rust I cleaned up with Lime-Away back when it still contained phosphoric acid. Naval jelly also contains it, but I wanted a liquid rather than a gel. Evaporust should do a fine job. In the RB mold that had an anomalous tumor of rust growing out into the cavity, I expected to wind up with a pit if I chemically removed all traces of rust, so I lapped it smooth and left the rest of the rust as the wall of the cavity at that location. It flaked a bit with use, but the castings don't show any positive material.

  18. #18
    Boolit Master FISH4BUGS's Avatar
    Join Date
    Jun 2005
    Location
    Inland from Seacoast New Hampshire
    Posts
    2,744
    There is a wealth of knowledge on this site, and having been here for almost 13 years, I have to say I have never had a question go unanswered.
    Many thanks to all.
    EvapoRust it is. The local ACE Hardware store has it in stock and I'll pick one up.
    Donald
    Collector and shooter of guns and other items that require a tax stamp, Lead and brass scrounger. Never too much brass, lead or components in inventory! Always looking to win beauty contests with my reloads.

  19. #19
    Boolit Bub
    Join Date
    Nov 2017
    Posts
    58
    A good rust remover, ( the folks here seem to know ) ..then rub the lead off, with a lead pencil...

  20. #20
    Boolit Master
    Join Date
    Mar 2010
    Location
    Michigan
    Posts
    1,200
    I have used a 1/8" piece of wood dowel with end tapered down to fit in grooves, & used JB compound to clean them up also.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check