ADvertise hereStainLess Steel MediaInline FabricationLee Precision
RotoMetals2Titan ReloadingGraf & SonsMidSouth Shooters Supply

Results 1 to 9 of 9

Thread: RCBS 10-10 missing feet

  1. #1
    Boolit Buddy metricmonkeywrench's Avatar
    Join Date
    Apr 2016
    Location
    Virginia
    Posts
    60

    RCBS 10-10 missing feet

    Being a bit too cold to go outside and play here in Virginia I finally turned my attention to my RCBS scale project on the reloading bench. I have a post down in the WTB section detailing the broken rear pivot feet, so I won’t re-hash it all here, but decided to go for a more permanent solution should a replacement base not be found to put it back in service.

    http://castboolits.gunloads.com/show...-stripped-base

    I took stock of my current capabilities and tooling and gave up on all the grandiose plans of machined blocks, precision adjustable feet and all other sorts of complicated detailed repairs and went a more realistic simple route. A short search of the wood scrap pile yielded a nice straight grain piece of oak which was cut to length then flanged on a radial arm saw to make a step to fit inside the base and fine-tuned to be level across the scale base. A little JB weld and a day later, (side note—is it ever possible to use this stuff and not find a dab of it stuck to the back of your hand or arm later on in the day?) I now had a place to add some semi-hard plastic stick on rounded feet from the hardware isle at Wally World. I figure if these hold up on the glass cutting board in the kitchen they should be fine for this. I leveled out the base with the zero screw and did the usual shuffle with the shot in the pan balancing act for this type scale and now everything is dead on repeatedly accurate across the board with the test weights (no surprise).
    Click image for larger version. 

Name:	10 10 block.jpg 
Views:	23 
Size:	56.7 KB 
ID:	211374Click image for larger version. 

Name:	10 10 feet.jpg 
Views:	21 
Size:	69.1 KB 
ID:	211375

  2. #2
    Boolit Master
    mdi's Avatar
    Join Date
    Jun 2008
    Location
    So. Orygun
    Posts
    4,994
    Cool!
    My Anchor is holding fast!

  3. #3
    Boolit Bub
    Join Date
    Sep 2017
    Location
    Near that little town in Eygpt or SW Wyoming, whichever
    Posts
    25
    Nicely done! Sometimes we over think a project but you came to your senses and did a good job. Speaking of the pan. A couple of years ago I found a project scale at a local pawn shop (505). Missing the pan. No Biggie! Just ordered up a replacement and put it to work----NOT! Old man with poor eyes and the shakes and about a bazillion 8 or 9 shot pellets. I finally got it set and only used a few dozen swear words and am good to go. I bought the pan on sale so I only have about 20-25 bucks in the deal. I like beam scales. No batteries or electricity of any kind, no tricky calibrations and repeat calibrations. It balances or it doesn't and you make an adjustment. Then you are good to go. I would like to have an older 10-10 but can't really justify the cost as the 505 and my old standby Redding work just fine. Again, I think you did a fine job and thanks for the pictures to go with!

  4. #4
    Boolit Master
    Join Date
    Aug 2013
    Posts
    173
    Good job - It'll still be working and doing it's job just same long after any current digital scale is in the bin.

  5. #5
    Boolit Master

    Join Date
    Mar 2013
    Location
    Northwest Ohio
    Posts
    7,794
    Nice looking repair there. It should last a long time for you. It may have been easier than replacing the body and getting it back right even.

  6. #6
    Boolit Master


    Taylor's Avatar
    Join Date
    Jul 2006
    Location
    Tennessee
    Posts
    1,459
    Missing feet- still able to work? Food stamps? Welfare? Disabled Social Security? Lots of possibilities.
    Pro Patria-Ne Desit Virtus

  7. #7
    PAPERPATCH MASTER


    Join Date
    Oct 2008
    Location
    Michigan Thumb Area
    Posts
    5,427
    Did you try contacting RCBS about those feet to be replaced yet?Robert

  8. #8
    Boolit Master copdills's Avatar
    Join Date
    Jul 2007
    Location
    South Carolina
    Posts
    674
    great job man , looks great

  9. #9
    Boolit Mold
    Join Date
    Apr 2015
    Posts
    3
    Bought an older used Lyman D7 scale. On one end it looked like it should have a couple feet or something in the holes underneath. It would not level without sliding something under that end, less than 1/4" thick. So I used what I had, 22 hollow point bullits. Taped a couple in and presto. Leveled and checked with my check weights, good old gray scale.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check