RotoMetals2Lee PrecisionADvertise hereGraf & Sons
StainLess Steel MediaTitan ReloadingInline Fabrication

Results 1 to 10 of 10

Thread: Mod Lee gauge shell holder for trimming brass

  1. #1
    Boolit Master
    Join Date
    Jul 2016
    Posts
    1,101

    Mod Lee gauge shell holder for trimming brass

    This is a simple shell holder mod to make it easier to lock in and loosen while seating and removing the brass your trimming using
    [quote from Lee]
    "The Lee Case Length Gauge & Cutter and Lock Stud is the simplest way to check the case and trim to the correct safe length."

    I just took a reloading die lock ring I had lying around (I'm sure none of you have any spare parts lying around ) and pressed the shell holder (OK I used a large pair of vise-grips [don't use visegrips, it goes in croocked] use a bench vise or ? would work better) into the lock ring (it's a really good fit) just to where you could still slide a case in and out then I thightened the allen set screw for extra secureing.

    The reloading die lock ring is a bit too rough so I'm going to spin it in some sandpaper to make it more comfortable

    I'm going to either epoxy the cutter into a wood ball from a reloading press handle to make easier to hold clamp it into a small vise (I think I'll go with the vise, it frees me from having to grab it on every case, I'm also thinking mounting the debring tips or use my RCBS trom mate without turning it on.









    Nothing earth shattering but I have 2500 pieces to do and can use all the help I can get.

    P.S. make sure you flare/enlarge the case enough to easily fit in the trim gauge
    I sanded /polished the trim guage diamiter down a little so the brass could slide over easier and that helped keep the brass from sticking to it and made it much easier to trim.
    Last edited by Grmps; 11-13-2017 at 07:34 PM.

  2. #2
    Boolit Man
    Join Date
    Mar 2016
    Location
    SE MISSOURI
    Posts
    106
    Neat ideal

  3. #3
    Boolit Master JBinMN's Avatar
    Join Date
    Feb 2017
    Location
    Goodhue County, Minnesota
    Posts
    775
    Thanks! I am going to try this in the next few days if I can.
    "If ya don't like my gate, ya don't have to swing on the hinges..." - L. Ackerman ( RIP)

  4. #4
    Boolit Master
    Join Date
    Jul 2016
    Posts
    1,101
    This is a quick stand I threw together to hold the cutter
    2x4, cut out a notch for the clamp to fit in, drill a hole the size of the cutter, cut a slot through the hole and 1 inch past it,
    slide in the cutter, clamp the slot together, stick 2x4 in drill press vise, clamp vise to the workbench.



    I ended up putting the shell holder and lock ring in a vise to true it so it would spin evenly.... much better now.
    Last edited by Grmps; 11-14-2017 at 04:30 AM.

  5. #5
    Boolit Master
    Join Date
    Jul 2016
    Posts
    1,101
    updated holder
    I drilled the 2x4 and threaded the deburring ends onto the board.

  6. #6
    Boolit Master
    Join Date
    Jul 2016
    Posts
    1,101
    converting 9x19 to 9x18 in nickel is a little hard for me with this lee die setup, wasn't as accurate as I would like so I switched to my old standard.


  7. #7
    Boolit Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    9,581
    Lee makes and sells a three jaw chuck that initially fit their Zip Trim - works great on a drill motor, just have to keep it clean.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  8. #8
    Boolit Master
    Join Date
    Jul 2016
    Posts
    1,101
    with the Lee
    Lee Precision 3 Jaw Spinner Stud

    thanks Wayne

  9. #9
    Boolit Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    9,581
    I used mine long enough that I had to take it apart to clean it and then get Lee to send me instructions for re-assembly! They did, too.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  10. #10
    Boolit Master

    Join Date
    Feb 2008
    Location
    Bozoland Mt.
    Posts
    1,305
    The die lock ring is a great idea, I will copy it soon, and a few times.
    I bought a lee 3 jaw chuck and never could get it to work, haven't mess with it for years, maybe it has grit in it.
    To lazy to chase arrows.
    Clodhopper

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check