RotoMetals2Lee PrecisionPBcastcoTitan Reloading
MidSouth Shooters SupplyLoad DataRepackboxWideners
Reloading Everything Inline Fabrication
Page 3 of 24 FirstFirst 12345678910111213 ... LastLast
Results 41 to 60 of 470

Thread: Star dies that I make

  1. #41
    Boolit Master
    lathesmith's Avatar
    Join Date
    Nov 2006
    Location
    Springfield, Missouri
    Posts
    1,373
    dd, Cayoot, HR, FN, PM, and others....thanks for the comments, it is nice to let other folks know that when it comes to the Star, they do have more than one choice when it comes to dies. Danny, sorry, I have never actually seen or used a Star that uses O-rings, so I don' t really know what to tell you to look for. Glad your stuff got there OK, it ought to keep you busy for a while.
    icm, I got your PM and will send a reply shortly.
    lathesmith

  2. #42
    Boolit Master

    mtgrs737's Avatar
    Join Date
    Jun 2007
    Location
    Kansas land of OZ
    Posts
    1,940
    Quote Originally Posted by ddeaton View Post
    Lathesmith, I got a box with a bunch of hardware in it when I back from out of town. I couldnt wait to size some of them. I had some 357s and 30s sitting waiting on these. Do you know what size the Orings are in the Magma? I must have nicked my top ring and now its leaking bad.
    Thanks again for the dies!
    Stop by your local Ace or True-Value hardware store and have a look in the plumbing department, take you old O-ring with you. I will bet that they have an exsact replacement there. You can use a caliper to measure the thickness of the o-ring and just eyeball the diameter. I have a couple of O-ring assortments that came from Harbor freight but they don't cover all the sizes and thicknesses.
    Mtgrs737
    Still Learning!

    NRA Life Member
    Life long OZ resident

    Personality type: Compulsive/Excessive - I don't know what that means, all I know is, if I like something, I want a lot of it!

    Pray to put "One nation, Under God" back in our country! We will never be a Great Nation without HIM!

    SOCIALISM is a PHILOSOPHY of FAILURE, the CREED of IGNORANCE and the GOSPEL of ENVY, It's inherent value is the EQUAL SHARING of MISERY. -Winston Churchill

  3. #43
    Boolit Master
    dragonrider's Avatar
    Join Date
    Apr 2006
    Location
    Linwood, Ma. USA
    Posts
    3,431
    I am assuming he means the o'rings on the lube piston. yes??
    Paul G.
    Once I was young, now I am old and in between went by way to fast.

    The end move in politics is always to pick up a gun.
    -- R. Buckminster Fuller

  4. #44
    Boolit Master ddeaton's Avatar
    Join Date
    Feb 2008
    Location
    SW Ohio
    Posts
    863
    No, the o rings in the die cavity. I am guessing this is only on the new Magmas? These seal the center lube cavity on the OD of the die when it is inserted in the sizer.

  5. #45
    Boolit Master

    Join Date
    Mar 2005
    Location
    NW Ohio, almost as N and W as you can be :-)
    Posts
    2,915
    Quote Originally Posted by ddeaton View Post
    No, the o rings in the die cavity. I am guessing this is only on the new Magmas? These seal the center lube cavity on the OD of the die when it is inserted in the sizer.
    Those O rings are a terrible "improvement" in the newer Star's...the dang thing gets rolled out of the groove by the lube in the relieved area of the die when your removing it, then it gets jammed in there.

    The solution I think is to cut an o-ring groove in the DIE right up near the flange and not put an o-ring in the groove in the lube sizer. I want to make some lube size dies of my own and I am going to try that.

    Bill
    Both ends WHAT a player

  6. #46
    Boolit Master
    dragonrider's Avatar
    Join Date
    Apr 2006
    Location
    Linwood, Ma. USA
    Posts
    3,431
    Didn't know they were doing that. I imagine it is cheaper to produce that way.
    Paul G.
    Once I was young, now I am old and in between went by way to fast.

    The end move in politics is always to pick up a gun.
    -- R. Buckminster Fuller

  7. #47
    Boolit Master ddeaton's Avatar
    Join Date
    Feb 2008
    Location
    SW Ohio
    Posts
    863
    that is why I nicked mine taking the die out and it got pinched. Magma suggests a light coat of oil on the die when inserting it. I think it is ok, just need to be aware and careful.

  8. #48
    Boolit Buddy rbwillnj's Avatar
    Join Date
    Apr 2005
    Location
    Northwest NJ
    Posts
    163
    Lathesmith, I sent you a PM, I need some of your sizer dies.

  9. #49
    Boolit Master

    mtgrs737's Avatar
    Join Date
    Jun 2007
    Location
    Kansas land of OZ
    Posts
    1,940
    Lathesmith is taking a little break with the family, he will be back on in a short time, he asked me to keep a eye out here for folks trying to contact him. Hold on for a short time and he will answer you.
    Mtgrs737
    Still Learning!

    NRA Life Member
    Life long OZ resident

    Personality type: Compulsive/Excessive - I don't know what that means, all I know is, if I like something, I want a lot of it!

    Pray to put "One nation, Under God" back in our country! We will never be a Great Nation without HIM!

    SOCIALISM is a PHILOSOPHY of FAILURE, the CREED of IGNORANCE and the GOSPEL of ENVY, It's inherent value is the EQUAL SHARING of MISERY. -Winston Churchill

  10. #50
    Boolit Master

    mtgrs737's Avatar
    Join Date
    Jun 2007
    Location
    Kansas land of OZ
    Posts
    1,940
    I have a used Star sizer that on some dies will oze lube from around the die, it most likely was worn or damaged at one time. The fix is easy, I wrap two or three turns of the teflon plummers tape around the top of the die and it stops the oze, it cheap, easy, and effective. Teflon tape varies in thickness so you will have to experiment with the number of wraps.
    Mtgrs737
    Still Learning!

    NRA Life Member
    Life long OZ resident

    Personality type: Compulsive/Excessive - I don't know what that means, all I know is, if I like something, I want a lot of it!

    Pray to put "One nation, Under God" back in our country! We will never be a Great Nation without HIM!

    SOCIALISM is a PHILOSOPHY of FAILURE, the CREED of IGNORANCE and the GOSPEL of ENVY, It's inherent value is the EQUAL SHARING of MISERY. -Winston Churchill

  11. #51
    Boolit Master

    Join Date
    Mar 2005
    Location
    NW Ohio, almost as N and W as you can be :-)
    Posts
    2,915
    Quote Originally Posted by mtgrs737 View Post
    I have a used Star sizer that on some dies will oze lube from around the die, it most likely was worn or damaged at one time. The fix is easy, I wrap two or three turns of the teflon plummers tape around the top of the die and it stops the oze, it cheap, easy, and effective. Teflon tape varies in thickness so you will have to experiment with the number of wraps.
    I did try using mine with NO O-ring and it oozed lube. Using the O-ring allows them a far wider size tolerance and less critical surface finish requirements. it is plan and simple a shortcut to the mfg process. What "grabs" the O-ring is the lube in the recess on the die, so I do not think grease will help there. I have had the most success pulling the die out partway, then snagging the O-ring with a hook shaped dental pick, then pulling it out over the die, then pull the die the rest of the way out. The deal is the O-ring gets pulled out of it's groove by the lube in the recess on the die, and no way can it get back in the groove to let the die come out. I have thought about trying a square O-ring, or gluing the O-ring in the groove with say permetex black silicone.

    I'm sure all the folks at Magma when I remove a die have to cool their ears with ice cubes .

    Bill
    Both ends WHAT a player

  12. #52
    Boolit Master
    Join Date
    Jul 2008
    Posts
    4,315
    Lathesmith, PM sent. Enjoy the family, see you when you get back. Jim

  13. #53
    Boolit Master
    lathesmith's Avatar
    Join Date
    Nov 2006
    Location
    Springfield, Missouri
    Posts
    1,373
    Well, we got back from Mexico today; tired but had a good time. It's kind of a tricky situation--do you post on the 'net that you will be gone for a week, or do you try and be a little more low profile? I chose low profile, and want to say "thanks" to those of you who helped me do this. Also, thanks to all you guys who are wanting to get some dies and were patient and understanding, I appreciate it. I will be working extra hard the next week or two to get caught up, if you haven't heard from me yet please send me another note. I'm only human, and it is easy to accidentally overlook a message. Thanks again, I look forward to getting back to the shop!
    lathesmith

  14. #54
    Boolit Master

    Join Date
    Dec 2008
    Location
    marengo,ohio
    Posts
    1,434
    lathesmith, I recieved the dies yesterday they look great not to mention the fast turn around time. Thanks again F.B.

  15. #55
    Boolit Master
    Join Date
    Feb 2006
    Location
    South of Saint Louie
    Posts
    1,986

    Question on star

    I am using some group buy moulds with BIG LUBE GROOVES, similar to the LYMAN 429667, and having problems getting the grooves filled. If I have all the holes in the die open, I get lube on the nose. (To add to the problem, yesterday I used wheel weight ingots I've been using for awhile and must have gotten some soft ones! so the boolits were .0005 to .001 undersize as cast. It was 70 degrees and I was getting busy and didn't think to check the hardness.)

    Any suggestions on a special hole spacing or size. I really like the 44 250 full wadcutter from OLD WEST BULLET MOULDS...it sucks up lube as bad as the LYMAN Cowboy Boolits.

    I'd appreciate a PM with your ideas...and address and price for a .431 sizer die for my STAR.


  16. #56
    Boolit Master
    Jon K's Avatar
    Join Date
    Mar 2006
    Location
    CA
    Posts
    1,756
    EDK,

    I assume you're using lathesmith's standard 3 groove die, right?

    I'm lubing Lyman 427666, RCBS 44-40 200gr, Saeco #420 (all big lube groove) I only use the 2 row center holes(Magma die).
    Once you have boolit aligned in the die, you may need to warm up the lube, if it's too hard, or give it an extra pump stroke for more lube.

    Jon
    Col 2:13-17

  17. #57
    Boolit Master



    Springfield's Avatar
    Join Date
    May 2005
    Location
    San Jose, California
    Posts
    3,684
    EDK; You are not suppossed to keep all the holes open, just one row of 3. Find the row that aligns with the lube groove when the bullet is at the lowest point and plug all the others with shot.

  18. #58
    Boolit Master
    Join Date
    Feb 2006
    Location
    South of Saint Louie
    Posts
    1,986

    Thanks

    I'm using MAGMA or STAR dies; White Label 50/50 lube. I broke down and hooked up the heater....that solved the problem for now, but I still need the .431 die....have .430 and .432 for the RANCH DOGS. I like to do minimal sizing.

    The lube gets darker when using the heater, but that shouldn't effect anything.

    Thanks again for the help. It's a d---- poor day that I don't learn something new on the forums.


  19. #59
    Boolit Master
    Jon K's Avatar
    Join Date
    Mar 2006
    Location
    CA
    Posts
    1,756
    EDK,

    lathesmith's prices are right, quick response and turn around time. You can't go wrong.

    Jon
    Col 2:13-17

  20. #60
    Boolit Master
    lathesmith's Avatar
    Join Date
    Nov 2006
    Location
    Springfield, Missouri
    Posts
    1,373

    multiple rows for one lube groove...

    EDK,
    I see there is a little confusion here about using multiple rows of holes for filling one lube groove. A die must be designed for this from the start; just opening up all the rows in a "normal" die made for muliple lube grooves obviously won't work, and just makes a mess.
    Cajun Shooter and I came up with a close-spaced row design, just for these oversize lube groove bullets. This design uses two rows spaced about .060 apart with the normal offset; this gets twice the amount of lube for the pressure and heat than a "normal" row of three holes. This allows you to work faster, and just generally seems to fill that large groove better. I suggest you send Cajun Shooter a PM, he can tell you more about how these dies work than I can.
    lathesmith
    Attached Thumbnails Attached Thumbnails lathe stuff 001 (Small).jpg  

Page 3 of 24 FirstFirst 12345678910111213 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check