Lee PrecisionStainLess Steel MediaTitan ReloadingGraf & Sons
ADvertise hereInline FabricationMidSouth Shooters SupplyRotoMetals2

Page 1 of 2 12 LastLast
Results 1 to 20 of 33

Thread: VS: 120v/220V PID setup

  1. #1
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509

    VS: 120v/220V PID setup



    Has a 600c 4 inch probe type thermocouple or a ring eyelet (limited quanity) for use on a Master Caster
    Has a 25 amp SSR for long life
    I can preset the temp on the PID if you like. Currently set at 700f

    $125 shipped anywhere a flat rate box will go.
    I will ship internationally. For International shipments, I will give you a $10 shipping credit for each PID setup, then you pay exact shipping cost. There is no restriction on shipping this item out of the country.

    Payment accepted - PayPal, USPS money order, Personal Check, Cash
    Last edited by HATCH; Today at 08:21 AM.

  2. #2
    Boolit Bub
    Join Date
    Apr 2009
    Posts
    28
    What is the output? Standard plug? More photos, I am very interested.

  3. #3
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509

    VS: 120v PID setup



    Plugs into a standard 120 outlet and can control 15 amps which is big enough to handle a master caster / master pot.

    It can do 20 amps no problem but I have yet to see a pot require a 20 amp 120v outlet.
    The plug that you plug your pot into the PID is a 15amp style plug
    Last edited by HATCH; 10-02-2017 at 10:13 AM.

  4. #4
    Boolit Mold
    Join Date
    Nov 2016
    Posts
    8
    Hatch,
    I will take one. PM to follow.

  5. #5
    Boolit Master jeepyj's Avatar
    Join Date
    Feb 2013
    Location
    Maine, Just north of Bangor
    Posts
    945
    Forgive for asking but I don't see how the thermocouple hooks up. Does it plug in the side or top that is not shown in the photo? Will there be instructions to change the temperature if 700 is not quite the desired heat amount? - jeepyj
    Sometimes it takes a second box of boolits to clear my head.
    Feed back thread http://castboolits.gunloads.com/show...?261449-jeepyj

  6. #6
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509
    I have a YouTube video on how to change it.
    https://youtu.be/1KsOk00zgZ0

    The picture I posted that shows the back is one that I had on my phone.
    The TC is hard wired in. It comes out where the power cables come out.
    To make it detachable would cost more money as its more work and more parts



    Sent from my iPhone using Tapatalk

  7. #7
    Boolit Master
    Join Date
    Aug 2014
    Location
    S W Louisiana
    Posts
    191
    I won the auction for the prototype of this unit. I am not a expert on these things, But it is well built with a Metal case that uses screws to hold it together. Doing any service work such as changing the thermocouple is a snap because of the design of the case. The PID and SSR are top quality components and should give a long trouble free service life. The small foot print takes up very little room in your casting area. In my opinion A very good bang for your buck. Hatch is very helpful if you need assistance. You cain't beat it with a stick. Iron Whittler

  8. #8
    Boolit Master
    Minerat's Avatar
    Join Date
    Jun 2008
    Location
    Jefferson County, CO
    Posts
    429
    Hatch, What's a "ring type"?
    Steve,

    Life Member NRA
    Member: Clear Creek County Sportsman Association


    Kilo Charlie zero Golf Papa Tango

  9. #9
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509


    On the Master Caster there are two threaded holes on the handle side of the Pot at the base side.

  10. #10
    Boolit Master
    Minerat's Avatar
    Join Date
    Jun 2008
    Location
    Jefferson County, CO
    Posts
    429
    ooohhh, Well I learned something new today, like my ma told me I should. Thanks for showing me. I thought it might be for a PC oven use.
    Steve,

    Life Member NRA
    Member: Clear Creek County Sportsman Association


    Kilo Charlie zero Golf Papa Tango

  11. #11
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509
    You can use it for that as well.
    Get a self tapping screw and screw this to the wall or ceiling of the oven away from the heating element.

    The probe type would be idea as you just drill a hole thru the wall of the oven and side insert the probe in.


    Sent from my iPhone using Tapatalk

  12. #12
    Boolit Master FrankG's Avatar
    Join Date
    Nov 2010
    Location
    Up on a hill in Southern Oregon
    Posts
    478
    I would be interested in a 220V model . What dimensions are they ?
    Thx Frank

  13. #13
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509
    they are 6x4x2

    Very small footprint
    The PID is a 1/32 size. Its the smallest size they make.
    I personally have used this exact model PID since 2012 on my Automated master caster and in fact on every Automation Panel I have built that had the PID option.

    The PID can be powered 85~260VAC/50~60Hz.
    Basically its wired internally the same as the 120 models.
    It will have 14ga pig tale coming out.
    On the 220 models I put 2 romex connectors on the back.
    One will have the pig tale and the TC, the other empty for you to put your pot wiring.

  14. #14
    Boolit Master FrankG's Avatar
    Join Date
    Nov 2010
    Location
    Up on a hill in Southern Oregon
    Posts
    478
    I got my 220v model from Hatch today and its a tidy little unit !

    Thank you Hatch !!

  15. #15
    Boolit Bub
    Join Date
    Apr 2009
    Posts
    28
    I recieved my hatch pid today. I am totaly impressed with the quality of this controller. I bought this because I had tried to make my own pid some time ago. The problem with a diy unit is getting a housing and punching all the holes and getting everything right. The hatch unit is top notch. The only real issue I have with this unit is that I set it outside by my truck. When I went back out an hour later my truck was not washed and waxed. I guess I expexted too much automation.

  16. #16
    Super Moderator


    HATCH's Avatar
    Join Date
    Sep 2008
    Location
    Lexington, SC
    Posts
    3,509
    Thanks for the review.
    I spent $150 on a rectangle knock out for the PID cutout and another $60 on a hydraulic hole punch set so I could use it.

    I try to make a commercial quality unit.
    The initial units were cut with a jig saw but I didn't like the way it ended up. Even taping the face before cutting, I ended up with scratches.
    With the knockout setup, I end up with a much better looking product.

  17. #17
    Boolit Master jeepyj's Avatar
    Join Date
    Feb 2013
    Location
    Maine, Just north of Bangor
    Posts
    945
    So let start off by saying I was on the fence about one of these for a while. Well quite frankly I'm glad I waited as I received mine yesterday and what a professional looking job. It is very well built, Nice slim profile, very easy to use. Thanks Hatch!
    Last edited by jeepyj; 11-22-2017 at 02:34 PM. Reason: grammar
    Sometimes it takes a second box of boolits to clear my head.
    Feed back thread http://castboolits.gunloads.com/show...?261449-jeepyj

  18. #18
    Boolit Bub Uncle Dave's Avatar
    Join Date
    Jul 2017
    Location
    St Charles, Mo.
    Posts
    29

    Great job Hatch

    I received my controller promptly from Hatch and it looks great. I just tried it out tonight heating a partial pot to let it learn and am very satisfied with it. Going to fill it up and cast this week with it. 👍

    Thank for the great product Hatch.

    Dave

  19. #19
    Boolit Bub Surfdog's Avatar
    Join Date
    Dec 2009
    Location
    Livermore, CA
    Posts
    41
    Quote Originally Posted by HATCH View Post
    Bump.


    Sent from my iPhone using Tapatalk
    Bump for a great product...thanks Hatch!

    Surfdog

  20. #20
    Boolit Master lablover's Avatar
    Join Date
    Aug 2015
    Location
    Macomb Michigan
    Posts
    288
    Quote Originally Posted by HATCH View Post
    Bump - 2 units ready to go.
    Will be 30 days before any more units are ready after these are sold.
    Might be longer because of the holidays.
    I hate waiting on parts. I hate even more when the parts I am sent (after waiting 45 days) are the wrong parts.


    I love a good report

    Hey Hatch. How would you mount this for a Lee 4-20 I may be interested

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check