Ballisti-cast Mark II Manual

[Ausglock]

G'day, All.

I have just bought a used but like new Ballisti-cast Mark II machine.
But... It came with no manual.
I have trolled the internet, but can't find a Manual for it in PDF (or any other format)
Anyone have one (machine or manual) they would be good enough to copy/send?

This machine nust have been one of the last out of the Ballisti factory as it has PID controller. Digi Timers etc.

Thanks.

[6bg6ga]

Trevor,

As good as you are simply draw out the schematics on the machine and it will all come into play. The mechanical portion of the machine simply employs common sense.

[Vegas Vince]

try search on this site or you tube?

[Hootmix]

New feller here,,Like Ausglock i'm looking for a any info on a "Ballisti cast Mark ii,,the last owner( has passed) left a lot of wires out of the main panel. No male plug on cord,,think it will be a 4-wire 30 amp ,, just need to know the proper sequence to put the wire's back in the main panel,,then I can go from there. It's just to nice a unit to let go to waste.


Thanks,,,Hootmix.

[Ausglock]

Hootmix.
Emails sent with PDF files of manuals.

[Hootmix]

Hey, Ausglock,,found'm this AM,,"Thank You" ,,the pot's are full of pure lead,,the other fell'a only cast for front stuffer's,,.Will be trying to get elect. hooked up today,,will send pics. via e-mail.

later,,,,,Hootmix.

[skeettx]

Great, looking forward to a report and
possibly pictures
Mike

[Hootmix]

Skeettx,,, you have a Ballisti Mark ii,,?


Later,,,Hootmix.

[skeettx]

Did, made too many bullets for my use, sold it to a friend
Have LOTS cast up and waiting their turn.
Question: 240V 60 HZ or 240V 50 HZ??
Mike

These standing at the ready if I ever run out of bullets

[Hootmix]

Skee,,, that is a very nice set of moulds!!!! I'v never seen that type before.



Later,,,,Hootmix.

[Hootmix]

Sorry Skeettx,,had to go look,,240v 60hz,,(set on 240v 50hz you loose 20% of load that's what the manual said,),


Later,,,,,Hootmix.

[skeettx]

Hensley and Gibbs 8 and 10 cavity moulds

https://www.youtube.com/watch?v=Z1bp8Cl3L8A

[Hootmix]

Well Skeettx,, i'm up hav'n warm'd over coffee,,& what ever that was in it,,ugh,,just watched the video,,now that is cool casting,,is that "YOU" ? I like the way you ( the person) rigged the rachet device,,thank's for shar'n.


Later,,,,Hootmix.

[skeettx]

Hello,
Back from goose and duck hunt
Cleaned the birds, ate lunch and now on the computer
Not me, but close, YES, I really like the sprue cutter devise
Mike

[Hootmix]

Glad y'a got to go. I spent the day on my mk2,,could not turn the cam's by hand,,,i think they were to tight ( other fellardid it ),,not sure if I did it right but,,loosened the 3 out side ring bolts( till I learn the parts by name) until the cam's turned easier. Then hooked the micro sw. next to rack & pinion,,to feed the drive sw.,,got the drive to turn the cam's without breaking the shear screw ( took 3). NOW !! need to figure out where the heater wires go to??? Like you I want to mould up plenty,,,then sell or trade this one. ( maybe).
any glad y'a had a gooood day.

Later,,,,Hootmix.

[sparky1954]

thanks for info on ballisti-cast II but it appears to be missing pages, and/or if you know anyone with a ballisti-cast I i sure could use a manuel for it including an electrical schematic. Anything would help.

[lisalisassc123]

Hello all. I am also searching for a copy of a manual for the Ballisti Cast Mark II machine. Can anyone out there help?