Lee PrecisionLoad DataInline FabricationRotoMetals2
Reloading EverythingRepackboxTitan ReloadingMidSouth Shooters Supply
Wideners
Results 1 to 18 of 18

Thread: Water storage system.

  1. #1
    Boolit Buddy OutHuntn84's Avatar
    Join Date
    Sep 2009
    Location
    Shawnee, Oklahoma
    Posts
    401

    Water storage system.

    Alrighty fellas do ya see any potential holes in my bucket?

    I want to have 110 gallons that gets rotated as I use the washer but can be my water reserve if we lose power. So the system will stay under pressure most of the time but will gravity feed to the tap in emergencies.

    Click image for larger version. 

Name:	kjjpk.jpg 
Views:	59 
Size:	27.9 KB 
ID:	204297

  2. #2
    Boolit Buddy
    Join Date
    Dec 2009
    Location
    SE Michigan
    Posts
    451
    Put a bypass valve in so you can work on the storage containers if needed.

    You should also install a feeder pipe reaching the bottom of each tank.

    That way fresh water will be changed out as it is used.
    Last edited by jaguarxk120; 09-19-2017 at 01:43 PM.

  3. #3
    Boolit Master
    farmerjim's Avatar
    Join Date
    Nov 2012
    Location
    St. Francisville, Louisiana
    Posts
    1,925
    You will need relief valves on the top of the tanks to allow air out on the first fill with water. You will need to open the valve on the top tank to let air in to use the water if the supply is turned off and you will want to use the water in the tanks.
    They do make valves that will do this automatically.
    There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand

  4. #4
    Boolit Grand Master jmorris's Avatar
    Join Date
    Aug 2007
    Posts
    5,268
    Looks like how my hot water heaters are plumbed, just no heaters in the tank.

    Only problem I see is the operating pressure and how strong your containers are there is a lot of SI in a 55 gallon barrel so it doesn't take a lot of PSI to make them fail.

    Let's say a 55 gal drum has a diameter of 18", this means the end of the drum has an area of about 250 sq. in. 40 psi of water pressure will exert a force of about 10,000 lbs on the end of the drum.

    A steel 55 gallon drum can take around 8 psi before it starts to come apart.
    Last edited by jmorris; 09-19-2017 at 07:09 PM.

  5. #5
    Boolit Master
    Join Date
    Sep 2016
    Posts
    2,377
    Also if stored outside make sure the drums have ultra violet protection built into the plastic. Regular plastic drums will only last about a year or so due to the UV rays.Frank

  6. #6
    Boolit Grand Master

    Join Date
    Mar 2013
    Location
    Northwest Ohio
    Posts
    14,455
    A lot of the old farm house here had a simple cistern in them that help water, It normally could be pumped in and some used the large roof areas and gutters to fill them. This wasn't potable water but was used for washing, flushing toilets and animals. The one in Dads old house was 10' X 12' X 48" or so to the bottom of the window access. Some were also set up under ground and brick walled these were filled from gutters, pumped or water hauled from the ditches as needed. Then used for animals washing and filling sprayers and gardens. No pressure on the holding tanks but the pump did give pressure when it moved the water. In order to gravity feed your tanks will need to be above the spigots. A couple bladder tanks may be better as they maintain pressure better

  7. #7
    Boolit Grand Master bedbugbilly's Avatar
    Join Date
    Sep 2013
    Location
    MI (summer) - AZ (winter)
    Posts
    5,098
    country gent - your description brought back a lot of memories of the farm houses up here in southern MI as well. Even my grandparents house in town, which was built in 1920, had a large cistern int he basement. It was probably 8' high and 12' X 12' - IIRC, thick concrete walls to withstand the pressure and lined with brick. It was strictly used to collect rainwater and in turn, used for washing, toilet flushing, etc. They had a shallow well for their potable water until the 1950s when the village put in a well, tower and water system. I remember that after my grandmother died in '63, my Dad was showing the house to a fellow who was a very good Baptist. When the got to the basement, he asked what the cistern was as I don't think he had ever seen one. My Dad was in a hurry as he had a funeral to get to so he just quickly replied,k "Oh, that's where my Dad kept his still." The guy did a double take but then realized that my Dad was pulling his leg. They walked upstairs and he bought the house on the spot and lived there for over thirty years before he and his wife passed.

    Another house in town - a large one that was basically a three story house as the attic was finished off, had a large storage tank in a portion of the attic that furnished water for flushing, washing, etc. that worked by gravity. It was fed by a "ram" for a stream on the property behind the house. Long gone now but I remember doing some carpenter work at the house and being able to see how it was set up - quite the thing!

    OutHuntn84 - good luck with your system - you'll get it figured out and will be glad you have it!

  8. #8
    Boolit Buddy OutHuntn84's Avatar
    Join Date
    Sep 2009
    Location
    Shawnee, Oklahoma
    Posts
    401
    Quote Originally Posted by jmorris View Post
    Looks like how my hot water heaters are plumbed, just no heaters in the tank.

    Only problem I see is the operating pressure and how strong your containers are there is a lot of SI in a 55 gallon barrel so it doesn't take a lot of PSI to make them fail.

    Let's say a 55 gal drum has a diameter of 18", this means the end of the drum has an area of about 250 sq. in. 40 psi of water pressure will exert a force of about 10,000 lbs on the end of the drum.

    A steel 55 gallon drum can take around 8 psi before it starts to come apart.
    My original thoughts were to use the blue plastic containers.... guess now its time to experiment with them outside my house to see if I can get them to fail versus in my house lol. Thanks for your input!!!

  9. #9
    Boolit Buddy OutHuntn84's Avatar
    Join Date
    Sep 2009
    Location
    Shawnee, Oklahoma
    Posts
    401
    Quote Originally Posted by country gent View Post
    A lot of the old farm house here had a simple cistern in them that help water, It normally could be pumped in and some used the large roof areas and gutters to fill them. This wasn't potable water but was used for washing, flushing toilets and animals. The one in Dads old house was 10' X 12' X 48" or so to the bottom of the window access. Some were also set up under ground and brick walled these were filled from gutters, pumped or water hauled from the ditches as needed. Then used for animals washing and filling sprayers and gardens. No pressure on the holding tanks but the pump did give pressure when it moved the water. In order to gravity feed your tanks will need to be above the spigots. A couple bladder tanks may be better as they maintain pressure better
    Yup that is right inline with some future plans for a non potable water system I have

  10. #10
    Boolit Grand Master jmorris's Avatar
    Join Date
    Aug 2007
    Posts
    5,268
    Quote Originally Posted by OutHuntn84 View Post
    My original thoughts were to use the blue plastic containers.... guess now its time to experiment with them outside my house to see if I can get them to fail versus in my house lol. Thanks for your input!!!
    Don't do it with just air pressure either, the result can be very violent. Use water as it is less compressible than air so the drum just spits when it fails vs...

  11. #11
    Boolit Buddy FrankG's Avatar
    Join Date
    Nov 2010
    Location
    Up on a hill in Southern Oregon
    Posts
    492
    A couple pressure tanks for a well water system would be a better solution and arent all that expensive . I have a 125 gallon pressure tank for my well that I installed when building our house .

  12. #12
    Boolit Buddy OutHuntn84's Avatar
    Join Date
    Sep 2009
    Location
    Shawnee, Oklahoma
    Posts
    401
    I was googling and youtubing on this and saw that one. Definitely better have a extra pair of shorts to change into lol. I'm just going to hook up a hose directly at the well cap where my pressure is the highest and see if or how long it can take the pressure.

  13. #13
    Boolit Buddy OutHuntn84's Avatar
    Join Date
    Sep 2009
    Location
    Shawnee, Oklahoma
    Posts
    401
    That would be an ideal solution Frank but checking the price those things run about a grand a piece... I can afford a $40.00 solution that would be awesome!

  14. #14
    Moderator Emeritus

    MaryB's Avatar
    Join Date
    Jun 2013
    Location
    SW Minnesota
    Posts
    10,304
    I used to use the Caged 250 gallon tanks outdoors. Held up for 4 seasons then I sold them, were still in good shape with no signs of deteriorating. One would be a lot easier to plumb than a pair of tanks. You can find them in food grade(often held olive oil or other oils) on Craigslist

  15. #15
    Boolit Grand Master jmorris's Avatar
    Join Date
    Aug 2007
    Posts
    5,268
    I was googling and youtubing on this and saw that one. Definitely better have a extra pair of shorts to change into lol.
    Just bleed out all the air so it's full of water before you let any pressure build. Results upon failure are much less dramatic, just wetter.

    The large caged tanks Mary is talking about are what they used as shields in the video above. You can store water in them and pump it out but they can stand even less pressure than the smaller drums before they come apart.

  16. #16
    Boolit Buddy FrankG's Avatar
    Join Date
    Nov 2010
    Location
    Up on a hill in Southern Oregon
    Posts
    492
    Source a couple used hot water heaters and gut and flush them out .

  17. #17
    Boolit Grand Master jmorris's Avatar
    Join Date
    Aug 2007
    Posts
    5,268
    Or just know that you have water in the ones in your house

  18. #18
    Boolit Buddy
    Join Date
    Apr 2016
    Location
    Central Michigan
    Posts
    238
    Another approach would be to use a non pressurized storage system. Don't have to worry about bursting barrels.

    An example is a farm stock tank or toilet. A float valve would keep the first drum filled to a set level (an open top drum may be easier to set up). Multiple drums can be daisy chained to give what ever capacity you want. A Shurflo style 110v on demand pump would provide outlet pressure to washer ect. A overflow tube can easily be plumed in as a safety device in case the valve sticks.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check