ADvertise hereRotoMetals2Graf & SonsLee Precision
Titan ReloadingInline FabricationStainLess Steel Media

Results 1 to 7 of 7

Thread: Drop of 'Super glue' under my pb checks?

  1. #1
    Boolit Master
    Join Date
    Mar 2013
    Location
    NE Nebraska
    Posts
    307

    Drop of 'Super glue' under my pb checks?

    So I realize pb checks aren't the perfect solution, but I need enough gc bullets to build a .45 Colt hunting load for my Blackhawk. I have some alum 'pop can' pb checks coming. I am shooting for 1200 fps with either the 45-270saa or the NOE 45-255rfp cast pretty soft, maybe 9.5- 10 bhn. My plan was to only size the very bottom band to .452, put a tiny bit of 'Superglue' in the check, then run them thru a slightly larger sizer with lube. I have a RCBS Lam II with Tac1 lube. Am I missing something? Other suggestions? With a check, I was hoping to use a softer alloy, than I think I should use with plain base boolets, running the same velocity.
    Thanks, hc18flyer

  2. #2
    Boolit Master PaulG67's Avatar
    Join Date
    Mar 2016
    Posts
    213
    At 1200 fps I would not bother with gas checks at all. I never use check in handguns, I will work with alloy or trying different powder/primers to get the results I want. Plain base boolits, no chamfers on the base.
    Paul Gauthier AKA Dragonrider


    I am Retired, I was tired yesterday and I am tired today!!!

  3. #3
    Boolit Man
    Join Date
    Jan 2011
    Location
    Prineville, Oregon
    Posts
    92
    Before you go to a bunch of extra trouble you should give your loads a try with plain-based and with the same boolit gas checked with the pb checks made by just checking the boolit in the size die like normal. I just got back from a range trip today where I did comparison shooting and the newly checked boolits shot significantly tighter than the pb boolits, and this was in a load which has been my standard for that revolver for 25 years now (1200 fps out of a .357). The pb checks I got from n.h. Schmidt seem to be on pretty danged tight without benefit of super glue -- run through a .357 size die in a Star.

    I got the checks to make boolits for shooting at higher velocities in my Rossi rifle, but my little test showed me that maybe it'll be worth using them for the revolver also. This surprised me-- I had always been of the same opinion as PaulG about the pb boolits in a revolver.

  4. #4
    Boolit Master

    DougGuy's Avatar
    Join Date
    Apr 2013
    Location
    just above Raleigh North Carolina
    Posts
    4,493
    Don't overlook dental wax either. You can get sheets of .060" dental wax cheap on fleabay, you cookie cutter them into a flared and charged case using a piece of wood or plastic to press them in and cut them, then seat the boolit normally. I have used these with magnum loads and they work fairly well. For what you want to do, they are certainly worth a try. Keep the alloy and the Tac1 as they are. Size to fit your cylinder throats or have them reamed to fit the boolit if they aren't big enough to slide a .452" through them with finger pressure.
    Got a .22 .32 .357 .38 .40 .41 .44 .45 .480 or .500 S&W cylinder that needs throat reaming? 9mm, 10mm/40S&W, 45 ACP pistol barrel that won't "plunk" your handloads? Shoot me a PM! Also on Facebook: https://www.facebook.com/Cylinderhone-756429174391912/

  5. #5
    Boolit Master

    Beagle333's Avatar
    Join Date
    Mar 2012
    Location
    Back in the woods a piece, just outside Auburn, AL.
    Posts
    4,654
    I'll often lay out 20-25 checks in a row and then put a speck of epoxy in each one and then seat and size. (epoxy gives a bit more working time than Superglue) I don't size anything before hand, I just press the boolit on the checks, then immediately run them backwards through a push thru sizer, then after an hour or so, I'll start back at the front of the pile with running them through the lubesizer as normal. The epoxy only needs about 5 minutes and it's ready before I go back through lubing.
    I do this with the pop can checks and also with my own Pat Marlin checks. I mostly do it because I'll often check, size and lube and then store in bags and the checks will get knocked off otherwise. I don't just check the ones I want to load, but make a good rainy day of doing a bunch of them at once. If you were going to load as soon as you checked and lubed, you might not need any glue at all.
    Colt 1860, it just feels right.

  6. #6
    Boolit Master

    kungfustyle's Avatar
    Join Date
    Feb 2013
    Location
    Central Florida
    Posts
    640
    I ran them through a lee sizer back end first and didn't have any problems with them coming off.

  7. #7
    Boolit Master Tenbender's Avatar
    Join Date
    Jan 2015
    Location
    Southwest Virginia Mountains
    Posts
    670
    Quote Originally Posted by PaulG67 View Post
    At 1200 fps I would not bother with gas checks at all. I never use check in handguns, I will work with alloy or trying different powder/primers to get the results I want. Plain base boolits, no chamfers on the base.
    Good advice. I went through the gc thing on 45 Colt. Now all I gc is my 45 carbine . The pistols don't need them. You don't need to load a 44 mag load in a 45 Colt. Keep it around 1100-1200 and you can kill anything in the lower 48.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check