MidSouth Shooters SupplyInline FabricationRotoMetals2Wideners
Load DataTitan ReloadingRepackboxLee Precision
Reloading Everything
Results 1 to 16 of 16

Thread: Dull spot on formica

  1. #1
    Boolit Buddy
    Join Date
    Nov 2011
    Location
    near Horicon Marsh in southern Wi
    Posts
    345

    Dull spot on formica

    Daughter spilled fingernail polish on formica kitchen table, leaving a dull spot the size of a small banana. Is there any way to restore this so it shines like the rest?

  2. #2
    Boolit Grand Master

    Join Date
    Jun 2013
    Location
    NW GA
    Posts
    7,243
    The nail polish typically removes all the oils from the surface. Is it dull but normal surface or didnit actuslly affect the surface of the Formica?

    I'd try some car wax to start with. I've used that on Corian when it was looking a bit dull.

  3. #3
    Boolit Grand Master

    mold maker's Avatar
    Join Date
    Jul 2007
    Location
    Piedmont (Conover) NC
    Posts
    5,429
    Much of the detail on Formica is actually printed, so care must be taken not to abrade the surface too much. If the surface is still smooth a coat of polymer wax will improve it, but the damage is done and we can only disguise it somewhat
    Information not shared. is wasted.

  4. #4
    Boolit Buddy
    Join Date
    Nov 2011
    Location
    near Horicon Marsh in southern Wi
    Posts
    345
    So other than wax, I understand that there is no product out there that will solve my problem? Not Good!!!!!

  5. #5
    Boolit Master
    farmerjim's Avatar
    Join Date
    Nov 2012
    Location
    St. Francisville, Louisiana
    Posts
    1,925
    Put a new Formica top on it. It is not hard or that expensive.
    There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand

  6. #6
    Boolit Master
    Join Date
    Apr 2005
    Posts
    4,900
    Does it have detail? I have seen smooth white formica, probably quite old, which didn't, and there may be other colours. With this you could polish away the texture with fine abrasive paper, say 600 and 1200 grit, and finish off with jeweller's rouge or something similar on a cloth or felt rotary wheel. It wouldn't take much thickness of melamine or resin to resist that.

  7. #7
    Boolit Master
    DerekP Houston's Avatar
    Join Date
    Nov 2015
    Location
    Houston, Texas
    Posts
    2,877
    Quote Originally Posted by farmerjim View Post
    Put a new Formica top on it. It is not hard or that expensive.
    We just put our new counter tops in and they are formica, are there any care instructions yall would recommend? It was ~10x cheaper than granite and the recommendation from my uncle was it would be easier to just replace in 5-10 years when we go to sell as tastes/styles will change over the years.
    My feedback page if you feel inclined to add:
    http://castboolits.gunloads.com/show...raight-Shooter

    Thanks Yall!

  8. #8
    Boolit Buddy
    Join Date
    Feb 2012
    Location
    Trenton, Fl
    Posts
    334
    For many years, lacquer thinner was the standard cleaner in cabinet shops to clean overspray contact cement from formica cabinets. Since nail polish is essentially lacquer, the polish should not have hurt the finish. Are you sure there was not a build up of wax or furniture polish on the table, and the nail polish removed that, showing the original matte finish?

    Leslie Sapp - Old school cabinet guy in another life.

  9. #9
    Banned
    Join Date
    Jul 2016
    Posts
    2,911
    When I installed plastic laminate I used Acetone (nail polish remover is similar) as a cleaner and it didn't affect the laminate at that time. Formica is almost all compressed paper with a thin layer of plastic on top.

  10. #10
    Boolit Buddy
    Join Date
    Sep 2010
    Location
    Tucson, AZ
    Posts
    368
    I made and installed counter tops for close to 30 yrs, there is a spray out there called Counter Magic, it's a cleaner with wax, might want to try that, the top surface is indeed plastic and we also used lacquer thinner as a cleaner.

    The weirdest damage I've seen was done by a lady cooling off baked potatoes on a paper towel on her butcher block formica, faded everything to a dull white where every potato sat, the manufacturer (thru a representative) paid to replace her counter then had us cut the damage out and send it to them, never heard what they found.

    For those with Corian, any damage can be polished or sanded with Scotch Brite pads, different colors are different grit with green being the roughest, we used purple which is medium and leaves a matte finish with white being fine for a glossier look, if it's a gouge or cut you may have to sand with fine sand paper prior to using the Scotch Brite, either way it becomes labor intensive because you may have to do the whole counter to get an even finish.
    "People in Arizona carry guns," said Detective David Ramer, a Chandler police spokesman. You better be careful about who you are picking on...

  11. #11
    Boolit Master
    DerekP Houston's Avatar
    Join Date
    Nov 2015
    Location
    Houston, Texas
    Posts
    2,877
    Thanks Tunnug! I will deff buy some 'counter magic' if I can find it. Easier to use the proper cleaner from the start then try to fix damage after the fact.
    My feedback page if you feel inclined to add:
    http://castboolits.gunloads.com/show...raight-Shooter

    Thanks Yall!

  12. #12
    Boolit Buddy
    Join Date
    Sep 2010
    Location
    Tucson, AZ
    Posts
    368
    Guess I've been out of the game too long, here's what I found, it was actually called Countertop Magic. http://www.superiorcabinet.com/counmag.html
    "People in Arizona carry guns," said Detective David Ramer, a Chandler police spokesman. You better be careful about who you are picking on...

  13. #13
    Boolit Master
    Join Date
    May 2016
    Location
    Hudson Valley NY
    Posts
    1,475
    We used acetone to clean Formica, nail polish remover will not harm it as I use it to remove nail polish left on Formica here. I think you have some residue left behind. Wipe it down good and try pledge on it. Formica is a laminated composite material composed of several layers of kraft paper impregnated with melamine thermosetting resin, or a unified core, and topped with a decorative layer protected by melamine, then compressed and cured with heat to make a hard, durable surface. If it's scratched you might try some plastic polish for lenses or extra fine buffing compound.
    Last edited by NyFirefighter357; 08-05-2017 at 07:16 PM.

  14. #14
    Boolit Buddy


    Join Date
    Nov 2009
    Location
    Oro Valley, AZ
    Posts
    284
    I had a dull spot on my formica. I told the neighbor kid to get off the counter and go home.
    "Only the weak blame parents, their race, their times, lack of good fortune, or the quirks of fate. Everyone has it within his power to say, this I am today, that I shall be tomorrow. The wish, however, must be implemented by deeds." Louis L'Amour The Walking Drum

  15. #15
    Boolit Master Handloader109's Avatar
    Join Date
    Jan 2014
    Location
    NW Arkansas
    Posts
    2,505
    I agree acetone, and most solvents won't harm Melamine. Heat can, mainly discolor the pigments and burn the paper. But not much else. If not Formica, then. There is no telling.

    Sent from my XT1097 using Tapatalk

  16. #16
    Boolit Master Just Duke's Avatar
    Join Date
    Dec 2007
    Posts
    4,502
    A large pencil eraser will polish the area back up

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check